M1950
-
220 Filler Cap Insert - S144
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Small Pump Leather - S85
Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.
-
427 Pump Cup - S82
Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point.
-
Military Funnel Aluminum - R303
This is a reproduction aluminum funnel and chain for the Coleman military lantern and 530 stove.
-
Vaporizer Screen - S164
Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.
-
M1950 Burner Bowl - E1271
New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.
These burner bowls will work on a 530 stove but you would need to use the M1950 generator and then swap the M1950 generator pricker rod with your 530 pricker rod. The bottom flange on the generator and the length are the same. I have tried this and it does work. May be a good option if you are desperate for a new 530 burner bowl.
You can also use the flame spreader off of it on the 530 stove. You will just need to grind the edges so they are pointed rather than square.
-
-
252 Filler Cap Chain Bracket - S20
This is the small part that attaches to the filler cap screw so you can hook the chain to it.
-
-
Milspec Chain Ring - S02
This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.
-
Filler Cap Screw 220 Size - S67
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
-
Needle Reproduction - S165
Reproduction needle for the 530 vaporizer. Will also work on the M1950 vaporizer.
-
Original M1950 Pump Leather - E1266
This is an original unused M1950 pump cup. It is folded due to being stored inside of the pump.
-
M1950 Spring - S140
This is the spring used in the non return valve located in the bottom of the pump. Reproduction part.
-
Check Valve Pip - S59
New rubber pip for the re-buildable NRV type check valve used on the 242, 242A, and the M1950 stove.
-
-
M1950 Pump Shaft No Handle - E1087
This is a used Pump Shaft for the M1950 military stove. It is just the pump shaft. Does not come with the handle.
-
Steel Vaporizer Screen - E1218
Steel NOS Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.