9F
-
Filler Cap Gasket for 3 Piece Cap - S41
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made of oiled leather.
-
Cap Gasket - S56
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
-
Check Valve Old Style - S179
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
-
Air Stem Old Style Long Used - E1358
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
-
Used Leather Pump Cup - E1436
These are used leather pump cups that fit most lanterns and stoves. They may need some oil and conditioning, but are still flexible. This is the typical sized 7/8" pump cups for most lanterns and stoves.
-
-
Filler Cap Gasket for 3 Piece Cap- 10 PACK - S41
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
-
Aluminum Funnel Small - R614
This is a new aluminum filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243 and similar lanterns or the 500 stove.
-
Pump Assembly, 220C Thick Steel Cap, Used - E1296
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
-
Pump Assembly, 220B Thin Brass Cap, Used - E1420
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
-
Air Stem Long New Style - E1048
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
-
Leather Pump Cup - 10 PACK - S81
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves. Has a 7/8 inch diameter and is made of oiled leather.
-
Pump Assembly, 220B Thick Brass Cap, Used - E1390
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick. Has a nickel plated brass cap.
-
Pump Brass Cap NOS - E1123
New old stock long pump for the model 220B and 220C lantern. These have a brass cap that connects the pump to the lantern. They have new pump leather on them. Probably made in the 1930's or early 40's.
-
Pump Assembly 220B Canadian NOS - E1149
This is a NOS pump assembly for the Canadian model 220B. It would also be correct for the 427 and 228B Canadian lanterns. The Canadian pump differs from the US in having a splined screw on cap rather than a checkered style.
-
Filler Cap Winged Used - E1590
This is a used winged filler cap that was used on the slant generator lanterns. Some models this was used on are: L220, 220B, 235, 4M, 2E,2F, 9E, AND 9F.
Comes with a new gasket installed.