325

Reproduction leather pump cup for Coleman lanterns and stoves. Fits many popular Coleman models that use a leather cup on the pump plunger. Good quality replacement that helps restore strong pumping action and keeps your lantern or stove working like it should.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Reproduction filler cap gasket for Coleman one-piece fuel caps. Fits many Coleman lanterns and stoves that use the 1-piece filler cap without a center bolt or screw. Good quality replacement that helps stop fuel leaks. If your cap looks like the one in the photo, this is the right gasket. 

Look HERE for how to install these. Green cap shown for illustration only and is not included.

Also known as part number 425A1361

Full Box of 50 packs (2 mantles per pack).

These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.

Also known as part number 425A1405.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.

Also known as part number 3000005094.

New Coleman-manufactured pump assembly designed for most lanterns and stoves. This assembly includes a neoprene pump cup and features interchangeable parts to match your specific existing setup. Note: This assembly is not compatible with small Peak 1 type products, which utilize a shorter pump rod.

Also known as part number 242J5201.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.

 O-Ring sizes are #6, #7, and #9, made of Fluorosilicone.

We know it does work on these models: 533 (need 2), 442

Does not work on the 400B, 508B, 533A, 3024

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Also known as part numbers 2000038026 & R214D046C.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

10-pack of reproduction filler cap gaskets for Coleman one-piece fuel caps. Smart value for many Coleman lanterns and stoves using the standard 1-piece cap without a center bolt. Keeps spares on hand so your gear stays leak-free on the next trip. 

Look HERE for how to install these. Red cap shown for illustration only.

Also known as part number 425A1361

This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many.  

Comes with a new gasket that you will have to install.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Amber globe with no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. 

This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Zippo brand Flints for the Coleman Lantern Spark Igniter.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

10-pack of reproduction leather pump cups for Coleman lanterns and stoves. Smart value so you have spares on hand for future trips. Fits the same Coleman models that use the standard leather pump cup. Helps keep your gear pumping smoothly.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a used pump square nut.

Comes with one square nut ONLY.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket for you to install if needed.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

Fuel Cap with pressure gauge.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

This is for one used 3 piece filler cap. They are in various stages of wear. Finish may be chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

Used Pump Assembly Spring

Spring ONLY

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. These are in rough shape, but will work fine.

These are all assorted colors that have missing paint, wrench parts, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

Reliable check valve removal tool crafted in the USA (Washington State), from high-quality steel. Designed for Coleman lanterns and stoves—handles both thicker original stems and slimmer modern ones with its two rods. Built to make the job straightforward every time. Backed by our lifetime warranty: if it breaks at any time, we will replace it or give you a full refund.

How to Use Your Check Valve Removal Tool

Important: Your tool is backed by our lifetime warranty against defects in materials or workmanship. As long as it's used correctly and breaks under normal use (not from misuse, excessive force, or improper engagement), we'll stand behind it. Contact us anytime with questions or issues.

Follow these steps carefully to remove and reinstall the check valve safely:

1. Identify the check valve type. Pull out the air stem (pump rod) and match its threads to one of the tool's rods: Large or Small. (Most pre-1980s Coleman models use the Large size; newer ones often use Small.)
2. Thread the rod into the check valve. Hand-screw the matching rod into the check valve threads, finger-tight only. Aim to bottom it out or engage as many threads as possible—adding a drop of light lubricant (like oil) can help if it's stubborn. Critical: If it only turns one or two rotations and doesn't catch properly, stop! That's not enough thread engagement, and forcing it could damage the valve or tool.
3. Assemble the tool. Slide the outer tube down over the threaded rod.
4. Engage the prongs. Gently rotate the outer tube until the prongs fully seat into the check valve's grooves/slots. (Note: On early valves, the fit may feel tight; on later ones, it may feel looser due to natural Coleman manufacturing variations—this is normal.)
5. Secure the assembly. Screw the wing nut onto the exposed end of the rod to lock the tube and prongs in place. Tighten it snugly by hand—do not over-tighten, as this could strip the valve threads.
6. Remove the check valve. Use a long crescent wrench on the tool's flats. Hold the fount steady (a second person helps here) and turn the wrench quickly counterclockwise to break it loose. If it's really stuck, tap the long wrench handle sharply with your fist or a rubber mallet for a controlled shock—often more effective than steady pressure. Once loose, finish unscrewing by hand.

To reinstall the check valve: Simply reverse the steps above.

• Tighten only until snug—do not over-tighten as you can damage your new check valve’s threads.
• No thread sealant is required, though a light lubricant on the threads can make future removal easier.

If you run into any trouble or have questions about your specific Coleman model, feel free to reach out—we're happy to help!

For more great Coleman repair tips and community advice, check out the Old Coleman Parts Collector forum: www.colemancollectorsforum.com

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.

These made in the USA Mica Globes measure 4 1/2" x 4 1/4" and fit models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This original globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417. Made in the USA. This globe is used.

This globe was originally made for the 5156 and similar propane lanterns but should fit models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 339, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417. Will ONLY fit these models that DON'T have the bail handle on the outside of the burner frame. Please see photos and inspect your model for fit. The openings at both ends are approximately 4 1/4 inch. It is 4 1/4 inch high.

This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A. 

Please see photos for condition.

Used Walmart Edition Sportsman Globe.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417.

Used nickel plated fuel cap. Fits most lantern and stoves except for a few models.

These are in rough condition and have wrench marks - will vary from what is pictured. 

Comes with a new gasket for you to install if needed.