9E

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.

It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole. 

Old part number 115-1361. 

This will not seal the typical Coleman lantern cap.

This 10 pack of gaskets are for many Coleman lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center like the example that is shown, then these gaskets will work. 

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.

Original NOS Coleman pump cup that fits most lanterns and stoves, they have been sitting around for many years and may not have their perfect shape. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Needle & Holder

Original NOS Coleman pump cup that fits most lanterns and stoves.

They are flat and have lost most of their shape from sitting around over the years

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.

This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.

This is a used pump assembly. It has a new pump leather installed.

Reproduction long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

New Old Stock check valve. Little tarnished, but show no signs of wrench marks. Check ball moves freely. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

This is a used pump assembly for the model 220b.  It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick. Has a nickel plated brass cap.

Used Old Style larger check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

The ball moves freely, but these have not been tested.

NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

Used Old Style check valve and air stem. Check ball moves freely. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

This is a used steel rough cast winged filler cap that was used on the early 220BX Lantern. 

Has a new gasket included for you to install if needed.

This is a used winged filler cap that was used on the slant generator lanterns. Some models this was used on are: L220, 220B, 235, 4M, 2E,2F, 9E, AND 9F. 

Has wrench marks, comes with a changed gasket.

This is a NOS pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.

Used old stock long pump for the model 220B, 220C, 220 Slant and 228 Slant lanterns, and many others. These are brass but are tarnished with age. Has new pump leather installed. Probably made in the 1930's or early 40's. THIS PUMP HAS A NON ROUND HOLE IN THE CAP. Please see photo. If you have a good cap you can use it instead or slip on a small washer inside to keep the spring from coming up through the hole. 

This is a NOS pump assembly for the model 220b.  It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick. Has a nickel-plated brass cap.