Other Brands

Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point. The inside diameter of the 427 pump tube measures .68 inches or 11/16".

This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

Filler cap gasket for the Prentiss Waber lantern. OD just under 1", ID 5/8".

O rings for the Thermos lantern and stove pumps. One is for the pump, the other is for the top seal. These are for the later model Thermos lanterns and stoves where the pump and filler cap where combined.

This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.

This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.

This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.

This also fits the AGM 2572 & Kamplite RL-3 

Cap gasket for Akron lanterns. Outside diameter is 5/8 of an inch. Inside diameter is 3/8 of an inch. Thickness is 1/8 inch.

Pointed Bottom Sears Lantern Replacement Decal

Decal for the Thermos lantern. It is approximately 2 1/2 inches long and is 1 1/4 inches high at the widest point. The background silver is too sparkly on these. Reduced price to sell.

Rectangle Later Sears Lantern Replacement Decal

Decal for Kamplite lanterns

Ted Williams replacement decal for Sears Ted Williams lanterns

NOS Akron generator for Lantern Models 131, 132, 132AG, 132G, 134G, 301G and Lamp Models 125 Utility, 140-BG, 140-B, 155 and Art Deco Models 486B7257 and 486C7258. May also fit Montgomery Ward Lanterns. The body measures 4 3/16 inches long. Does not come with packaging.

This is a gasket sealer that many use for sealing valves to tanks. Is flexible when dry and offers good fuel resistance.

Decal for the Thermos "Holiday" lantern.

Reproduction generator for the Sunshine Safety lanterns and lamps. Similar to the Coleman Q99 but has a different nut. Will not work on Coleman lanterns and lamps.

AGM lantern screen retainer. Has an approximate diameter of 7/8 of an inch. This holds in the burner screen to the burner frame. Fits single mantle models like the 3016, may fit others. The 200A burner screen HERE will fit in these burner frames if you trim it a little with scissors.

This is an AGM made generator that will fit many AGM models.  Does not come in original box. Box is just to show application. Fits the below models and probably many others. Tube width is 1/4". Overall length is 3-11/16" long.

• AGM model 3927
• Prentis Wabers L43S
• Sears 7426
• Kamp Lite  RL2
• Akron 132S
• Coleman 220/228 models

Burner cap. Similar in size to the Coleman 220 burner cap.

Decal for the AGM model 3016 Lantern. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Gas tip for Thermos stoves.

Decal for Montgomery Ward Hawthorne lantern.

Burner screw for Thermos stoves.

Fuel needle. Measures 3 7/8 inches long.

Preway Stove Generator Gas Tip for 401, 402, 404, 409, 4521, 4522, 4521A, 4522A, 4821, 4822

Generator for AGM lanterns. Measures 3 1/8 inches long. Fits the AGM model 3025 lantern, may fit others. 

This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:

Fuel tube. Measures 2 1/2 inches long.

Pump. Measures 5 3/4 inches long.

Valve stem for thermos stoves.

Burner cap with 5 holes for thermos lanterns.

Burner ring for Thermos stoves. May show signs of light rust.

Fuel tube and screen for Thermos stoves. It is 3 inches long.

Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.

This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.

This horizontally striped frosted globe is approximately 3 7/8 inches tall and has a 4 3/8 inch diameter.

Thermos generator for models 8489, 8490, 8491 stoves. New generator includes new gas tip, spring, and tip cleaning wire.

Gas tip hood for Thermos stoves.

Burner cap with 3 holes for Thermos lanterns.

Fuel tube. Measures 3 1/8 inches long.

Generator nut for Thermos lanterns.

Term-Sport Alcohol Stove Gasket Set. These gaskets are for the filler cap and the burner tube. Both are made from fuel resistant materials that will last for years (ECH - Cap & Viton - Burner Tube).

Thermos generator for stove models 8420, 8421, 8430, and 8431. New generator includes new gas tip, spring, and tip cleaning wire.

Used bail handle for many smaller 1 mantle AGM, Kamp Lite, Sun Flame, Kook Lite and JC Higgins lanterns.

Used valve for the model 8326 Thermos lantern.

Decal for the Punker Alcohol Stove. This decal is the waterslide type - not peel and stick. 

Click on the "Description" under the photo to see the installation instructions.

Used collar for the Thermos model 8326 lantern.

New old stock generator for the Aladdin PL1 lantern.

Term-Sport Alcohol Stove Tank Decal. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.