Stove Parts
-
Leather Pump Cup - S81
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
-
Filler Cap Gasket for 1 Piece Cap - S42
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
-
Large Valve Stem Packing - P01
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
-
Small valve stem packing - P02
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
-
5114 Propane Gasket - S53
This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.
This fits many applications for propane appliances.
-
O Ring - S23
O ring made of gas resistant Viton. Outer diameter 7/16". Works on many propane stove models such as 5400A.
Two required for the model 550 stove.
-
Leather Pump Cup Kit - C005
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
-
Filler Cap Screw 220 Size - S68
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
-
M1950 Pump Rebuild Kit - K05
This is a complete rebuild kit for the pump on an M1950 stove. You will get the cap gasket, check valve dot, fuel tube gasket and pump leather.
-
Pump Assembly, Universal - C006
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type. -
Check Valve O Ring - S20
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
-
Valve Wheel Screw - S77
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
-
Pump Cup, Neoprene - C019
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
-
-
5423A5611 Gasket - S43
This is the gasket only from the 5423A5611 small parts kit. OD 1/2", ID 3/16", Thickness is just under 1/16" Was commonly used on the model 5413, 5413A, 5423, 5430B, 5433, 5430B, 5430C, 5435C, 5435D and similar propane stoves.
-
Small Pump Leather - S83
Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.
-
-
-
-
Pump Assembly Leather Used Square Nut - U810
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
-
Coleman Campstove Decal - D25
Coleman Decal For Pre-1963 Camp stoves. These are large decals and are for suitcase type stoves. Small stoves like the model 502 would use a lantern decal D11. This decal measures approximately 3 1/4 inches wide and is 1 1/8 inches high.
-
530 Diffuser Plate - R505
This is a reproduction flame diffuser plate for the 520 and 530 stoves. These are very nice plates. Professionally cut. 4 inch diameter.
-
Cap Gasket HGP - S50
This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
-
Burner Cap & Rings - C54
Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves
-
-
Valve and Generator - C29
New Coleman made valve and generator. This part will fit: 2G, 2H, 9A, 9B, 9G, 9H, 415C, 415D, 416B, 416C, 421, 421C, 421D, 421E, 425, 425B, 425C, 425D, 425E, 425F and Sears 476.72301, 476.74960, and 476.72244.
-
-
Pump Cup & Nut, Neoprene - C008
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091 -
M1950 Burner Bowl - E1271
New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.
These burner bowls will work on a 530 stove but you would need to use the M1950 generator and then swap the M1950 generator pricker rod with your 530 pricker rod. The bottom flange on the generator and the length are the same. Others have tried this and we are told it does work. May be a good option if you are desperate for a new 530 burner bowl.
You can also use the flame spreader off of it on the 530 stove. You will just need to grind the edges so they are pointed rather than square.
-
Vaporizer Screen - S159
Vaporizer screen for the model 530 stove. Would also work in other similar military stove vaporizers such as the M1950, 523 and 520. To install, roll between fingers to reduce diameter slightly, and insert into generator/vaporizer.
-
-
Valve & Generator - C33
New Coleman made valve & generator. This part fits: 413B, 413C, 413D, 413E, 413F, 413G, 426D, 442, Sears 476.72302, 476.72303, 476.74970, 476.74980
-
Coleman Stove Decal - D32
Coleman Logo for Camp stoves Made After 1963. These are large decals and are for suitcase type stoves. Small stoves like the model 502 would use a lantern decal D11. Measures approximately 3 1/4 inches long and is 1 1/8 inches high.
-
Needle Reproduction - S92
Reproduction needle for the 530 vaporizer. Will also work on the M1950 vaporizer.
-
Check Valve Old Style - R425
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
-
Small Pump Plunger - C35
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.
-
-
M1950 Spring - S141
This is the spring used in the non return valve located in the bottom of the pump. Reproduction part.
-
Auxillary Burner Bowl and Rings - C53
Auxiliary Burner Bowl, Rings And Screw 413E/413F/413G/424/426B/426/D/426G/442/442A/443 Instant Light, 2 & 3 Burner Stoves
-
-
Red Knob - S172
This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original. -
-
Regulator Screw On - C79
Regulator screw on. If you want the clip on regulator then it would be 9942-5251.
-
-
-
Valve Wheel Red Old Style, Used - S111
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
-
Burner Ring Gasket Material - R515
New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉.Sheets are 4-3/4" in diameter and 1/32" thick.
-
Valve Minus the Generator - C43
Valve minus the generator for the model 425 series stoves.