325A

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The green filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Full Box of 50 packs (2 mantles per pack).

These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Replacement Filler Cap New brass one-piece filler cap manufactured by Coleman. Includes a new gasket. This part fits most Coleman lanterns and stoves. It is not compatible with model 242 lanterns or model 500 stoves, which require the smaller size filler cap.

Also known as part number 425A1405.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

Replacement Pump Assembly Parts New leather pump cup, push-on nut, and back-up plate set. This kit is designed to fit almost all Coleman lanterns and stoves.

Also known as part number 3000005094.

New Coleman-manufactured pump cup designed for all lanterns that originally utilized the rubber-style cup.

Also known as part number 639-1091.

New Coleman-manufactured pump assembly designed for most lanterns and stoves. This assembly includes a neoprene pump cup and features interchangeable parts to match your specific existing setup. Note: This assembly is not compatible with small Peak 1 type products, which utilize a shorter pump rod.

Also known as part number 242J5201.

They are approximately 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.

 O-Ring sizes are #6, #7, and #9, made of Flourosilicone.

We know it does work on these models: 533 (need 2), 442

Does not work on the 400B, 508B, 533A, 3024

This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

They are approximately 10 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. Is enough to use on about two to three lantern bails.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This nickel plated filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.

Also known as part number 425A1361

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

Amber globe with no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. 

This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

These are treated with Thorium from the factory and work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.

Zippo brand Flints for the Coleman Lantern Spark Igniter.

This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a used pump square nut.

Comes with one square nut ONLY.

This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. 

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket that you will have to install.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

This is a used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by picking out the ones in best shape first.

We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.

Comes with a new gasket for you to install if needed.

Original NOS Coleman pump cup that fits most lanterns and stoves.

They are flat and have lost most of their shape from sitting around over the years

Has a 7/8 inch diameter and is made in the USA of oiled leather.

Fuel Cap with pressure gauge.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

Used Pump Assembly Spring

Spring ONLY

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

This is used check valve, the ball moves freely, but these have not been tested.

This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.

If your part diagram calls for the 242B5381, 200-6381 or a 621-5361 check valve then this would be the correct part. Also known as part number 2006381ZCL.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove. Wear and finish will vary. Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. These are in rough shape, but will work fine.

These are all assorted colors that have missing paint, wrench parts, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.

Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup. 

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.

These made in the USA Mica Globes measure 4 1/2" x 4 1/4" and fit models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5153, 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.

It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

Used Pyrex picket globe for the model 288 and similar sized lanterns. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. 

This globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417.

This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.

This is a used one piece filler cap off the Model 286 most likely. 

Comes with a new gasket that you will have to install.

This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A. 

Please see photos for condition.

This globe was originally made for the 5156 and similar propane lanterns but should fit models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 339, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417. Will ONLY fit these models that DON'T have the bail handle on the outside of the burner frame. Please see photos and inspect your model for fit. The openings at both ends are approximately 4 1/4 inch. It is 4 1/4 inch high.

Used picket globe for the model 288 and similar sized lanterns. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417.