- Free Shipping
Decal - Fits 1951 200A & 1951 thru 1954 220 & 228E Lanterns - D17
Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns
Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns
Coleman Lantern Logo for 1955 to 1961 220 & 228 E Lanterns
No Border Logo with "Reg." & "Lantern" for 1961 to 1964 200A, 220 & 228 E & F Lanterns
This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.
This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)
NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62.
Has paint chipping and some rust (see photos)
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-65.
Has paint chipping and a couple scratches/scuffs (see photos)
This is a used old style fount for the 220/228B through 220/228F lanterns.
Has small scratches/scuffs, chips and looks like some plastic got melted to the outside but might be able to get it off (see photos).
Used direction disk for the earlier double mantle lanterns such as 220/228B, C, D, E, and F. Will show signs of wear but still be in good condition. May be a transition disk between the 70's & 80's model lanterns.
Used guillotine carry case for all large hat 228 style lanterns. Will also fit 220, 275, 290, and 295.
Latch works great - has some rust, scratches and a couple dents (see photos)
This product is not included in the OCP free shipping program.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.
Used Smith-Victor carry case for all large hat 228 style lanterns. Will also fit 220, 252, 275, 290, and 295.
Has some scratches, one edge is bent a little but doesn't hinder the case closing, both latches aren't perfect on latches tight but is a little bent, the other latch is loose but still closes.
This product is not included in the OCP free shipping program.
This is a used older style brass mixing chamber for the 220-228 series lanterns.
This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.
This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.
This is a newer style mixing chamber for the 220-228 series lanterns. It is plated with a zinc coating or something similar.
This is a used mixing chamber. May or may not have a vent rod and air tube screw.
Mixing chamber for lamps and lanterns. It has the burner tube holes at a wider spacing than the normal mixing chambers. The burner tube holes are 1/1/2 inches apart center to center. Normal mixing chambers are spaced 1 3/8.
New reproduction direction disk for the many of the 2 mantle lanterns made in the USA like the 220 and 228 models B thru F. These are aluminum and look and feel identical to the original, and they are made here in the USA. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantles" as opposed to "mantle" for a single mantle lantern.
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.
New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Round steel burner cap for most models of double mantle lanterns and lamps.
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.
Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.
Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
This is a 10 PACK of the cardboard tube that goes inside of the 200A and 220 size generators, and many others.