- Free Shipping
O-Ring Single #9 - S22
O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone.
We have been told that these will fit the 533 Stove - 2 are needed.
O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone.
We have been told that these will fit the 533 Stove - 2 are needed.
New generator needle. This is a reproduction part. This fits the 321, 331, 335 and the 339 models.
Used bail for the models 321, 325, 331, 335, 339 and other similar Canadian models.
New generator includes new gas tip, spring, and tip cleaning wire.
This fits the 321, 331 and the 335 models.
The Canadian 990 globe was made to fit the model 331 lantern. Does not fit any other gas lantern model. Very rare globe to find these days. Will also fit the Thermos lantern models 8311 and 8312.
NOS Coleman shade holder for the old CQ style lamps.
May have a little rust from sitting around all these years.
Used gas tip for the Q99 generator and some Quick-Lite Lanterns and Lamps. Very tarnished
Used burner assembly for the old model 327,427, also for CQ and Air O Lite lanterns. Will also work on other lamps that would have originally taken the Q99 generator.
Valve stem for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.
NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.
Steel air intake tube for the old Quicklite lanterns and CQ lamps.
Reproduction Q99 generator for the old Quicklite style lanterns and lamps. They work great.
Used red carry case for lanterns. Fits models 200, 200A, 200B, 201, 202, 288, 286, 321B, 335 and other smaller sized lanterns.
Has some scratches and a dent on the top (see photos)
Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.
O-Ring sizes are #6, #7, and #9, made of Flourosilicone.
We know it does work on these models: 533, 440, 442
Does not work on the 400B, 508B, 533A, 3024
Used red carry case for models 200A, 288, 286, 290, 290A, 295, 220 F-K, 321, 327, 427 and Quick-Lite Lanterns.
Latches work great.
Used black carry case for models 200A, 288, 286, 290, 290A, 295, 220 F-K, 321, 327, 427 and QuickLite Lanterns.
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
Aluminum mixing chamber for most double mantle lanterns and lamps. Coleman experimented with aluminum for a few parts back in the old days. I believe it was discovered that aluminum could not hold up to the heat. Probably more of a display piece than for using.
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.