Filler cap gasket for the model 523 military stove.
Coleman #51 Mantles. 2 per pack Fits models 3018, 3023, 3112, 5130, 5132, 5133, 5134, 5136, and 9742
Also known as part number 2000026608.
Made by Coleman #51 Gold Top Mantles. 2 per pack. Fits Leisure Line Lanterns and most bayonet type lanterns Requires no tying or cutting of string Claims to be 4 times tougher than standard mantles
Decal for the early Coleman LP lantern.
New fount for the model 635 & 639 lanterns.
This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.
This fits many applications for propane appliances.
These are new fuel rated valve cores and will fit the 214, 275, 275A, 285, 286, 288, 288A, 290, 290A lanterns and also the 400, 400A and 508 stoves.
These will function for Off/On in the following stoves, but may not allow full flame control, particularly at the low end of flame adjustment: 400B, 440, 442, 3024, 508A and 533.
Need more information on the valve core? Click HERE.
Valve Complete for the 5107 and 5107A propane Lantern
New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉.
Sheets are 4-3/4" in diameter and 1/32" thick.
Vent rod for the model 5114 propane lantern.
This is an original old red letter replacement logo globe made in USA. This globe will fit models 5107, 5151, and 5152. The globe is approximately 4 inches tall. The top diameter is 5 inches. The bottom diameter is 3 13/16 inches.
This is the small check ball for the 427 lantern with an external pump. In the photo below, you can see the application. These are made from 440C Stainless Steel, the original was brass.
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..
This is a screw for 242 pumps where the top of the pump fits inside the fount and for other applications with this thread.
This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:
Used Lantern Base Dark Green.
Bail Handle 5151A, 5151B, 5151C, 5152A, 5152B, 5153A, 5154, and others.
Burner frame assembly for the model 5152A lantern.
Parts kit for the model 5151A propane lantern. Includes heat shield, vent bracket, 2 gaskets and nut.
Valve for the 5154B, 5152D, and 5153A propane lanterns with electronic ignition. Comes with ignitor cam and knob/screw.
Spacer for lantern models 5154B, 5152D, 5153A, 5151C and 5150
Collar assembly for the model 5107 and 5107A lantern. New old stock but has some scratches.
Generator for the 5101 and 5101A lantern. Brass, not nickel plated.
Vent bracket.
Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern.
Fits the model 5114 and 5114A propane lanterns
Used handle for the 511A, 512, and 512a heater.
Fits the model 5122 propane lantern.
New old stock filler plug for catalytic heater.
Used bail handle for a catalytic heater.
Frame assembly for Leisure line lantern
Used Vent bracket.
Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern.
Air stem for heater 4, 5, 5A, and 7. Measure 14.25 inches long.
