Search
200 Burner Frame Washer Kit - K14
These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.
New 200 burner frame Pal Nut is HERE.
New 200 burner frame Nut is HERE.
Burner Frame Stainless - R350
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
Burner Frame, Used - U930
This is a used old style burner frame originally used on the black band 200A Lantern. Looks like someone may have replaced the tabs - they are supposed to be short.
- New!
242 Burner Frame, Used - BF504
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
Is stamped with 3000.
- New!
242 Burner Frame, Used - BF505
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
This one will need a new burner cap or screen.
Is marked with 3000.
220 Burner Frame, Used - U920
Used burner frame that will fit models 220B through early 220F through approximately 1971.
- New!
242 Burner Frame, Used - BF503
This is a used Burner frame for the 242A through C lantern. Will also work on the 247.
Is stamped with 3000.
200A Reproduction Burner Frame - R353
This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
159 Lamp Burner Frame, Used - E1310
Only 1 left in stockBurner frame for the 158, 159 and 159X kerosene lamps. May fit others too. Valve turns and seems to operate smoothly.
- New!
- New!
228 Burner Frame, Old Style, Used - U923
Only 1 left in stockThis is a used burner frame that will fit models 228B through 228F.
Has a bit of rust
Lamp Burner Assy with Valve & Generator, NOS - E1002
Only 1 left in stockNOS burner frame, Valve and Generator for the 158, 159 and 159X kerosene lamps. May fit others too. Very nice condition.
M1950 Burner Bowl - E1271
New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.
These will not fit the 530 stove without using a 1950 generator and a 530 needle.
AGM Burner Tube - E1145
I believe these are burner tubes for an AGM double mantle lantern. They are 2 7/8 inches long. Roughly the same diameter as Coleman burner tubes. Made of steel.
Burner Button #2 - E1314
Unknown ceramic material type of burner button used on some heaters and stoves. This has a diameter of 3/4 and is 3/4 tall.
Unknown Burner #7 - E1582
Don't know what this came from. It is about 4 7/8" long, the smallest end is about 3/4" wide and the biggest end is about 7/8" wide. From wing to wing it is about 2 1/2" wide.
Focus 5 Burner Ball Reproduction - R703
This is a reproduction burner ball for the Focus 5 heater. Has been field tested and works excellent. Comes with instructions on how to remove the screen from your old ball and install the new - see those instructions in the "Description" area below. Made of stainless steel. The smaller inner screen would need to be good on your current burner for it to work correctly. Made in the USA.
- Free Shipping
Burner Screen - S29
This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.
- Free Shipping
- New!
Thermos Burner Assy, Used, 2 Mantle - V108
Used burner assembly for the Thermos 2 mantle lantern. In good shape.
Burner Ring Gasket Material - R515
New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉.Sheets are 4-3/4" in diameter and 1/32" thick.
Frame to Valve Nut - S64
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
220F Vent, Small Frame - U880
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
228F Vent, Small Frame - U886
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping and one small dent on the outer rim (see photos).
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
228 Vent, Small Frame, Used - U887
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
220F Vent, Small Frame - U882
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
290 Frame Bottom, Used - E1504
Used frame bottom plate for the model 290A and all 295 models. This is a used part and conditions vary one to another.
- New!