Burner cap. Similar in size to the Coleman 220 burner cap.
New old stock filler cap and chain for the military lantern. Will also fit any Coleman lantern or stove that used the standard size filler cap. I am 99% sure these filler caps came from the old SMP factory.
Top cap for the Leacock lamp handle.
NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.
Cap Gasket for M1942 & M1950 stoves.
Cap gasket for Akron lanterns. Outside diameter is 5/8 of an inch. Inside diameter is 3/8 of an inch. Thickness is 1/8 inch.
Drain cap for the KampKold cooler.
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
Reproduction filler cap insert for the older winged style filler caps used on model 427 lanterns. Comes with the new gasket.
Used Air flow restrictor cap for the model 159X lamp.
This is a cap for the end of the M1950 pump. This screws into the bottom of the pump.
This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
Jug cap that fits most Coleman jugs. Does not have a gasket - this is the cap only. Will need a gasket to seal well.
Large filler cap for kitchen ranges and other large appliances. New old stock but has a new gasket installed.
Burner cap with 3 holes for Thermos lanterns.
Burner cap with 5 holes for thermos lanterns.
This is the small part that attaches to the filler cap screw so you can hook the chain to it.
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves
This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
This is a reproduction filler cap insert for the large filler caps as used on Handy Gas Plants, Radiant Heater #2, Remote Tank 457 and 465, and other large tanks.
New, reproduction burner cap for 321, 331, 335, 339, 621, 625, 635 and 639 lanterns. Solid brass with stainless steel screen.
Also known as part number 335-315
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
This is a used snuffer cap.. Will fit only the 513 and 513K heaters.
This is a NOS filler cap insert for the large filler caps as used on Handy Gas Plants, Radiant Heater #2, Remote Tank 457 and 465, and other large tanks.
Filler cap lanyard for the small backpacking lanterns.
Filler Cap For Northstar Lantern - 2000-750T 2000-750 2000-750E 2000A750. New part number 3000005380.
Comes with a new gasket that you may need to install.
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242 and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.
NOS, HGP cap. Fits models 457, 457G, 575, 460, 470G Handy Gas Plants. Also fits the 465 Tank.
This is a reproduction nickel plated brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
Reproduction iron filler cap. Fits most irons and other appliances that take a small filler cap.
Filler cap. Appears to be made of aluminum. Roughly the same size as the common Coleman filler cap.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
Filler cap gasket for the Prentiss Waber lantern.
Filler plug gasket for the model CQ lamps,327 Quicklite lanterns and many older stoves. Can be used in place of the 104-136 lead gasket. Also fits the 523 military stove.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
New burner cap & screen for the model 236, 237 and 249 lanterns.
Solid brass with stainless steel screen.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
