This is a shade standoff for a non Coleman Lamp. The threads are too big for the Coleman mixing chambers. It is typically used to mount a paper shade on a lamp with a glass globe in place.
Post is 5/16" Wide in diameter, end to end is 2 5/16" long, end to base of threads is 1 15/16", and the outside thread diameter is 15/64"
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:
Used fluted lamp fount top. Looks like this fount top was painted purple before.
This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.
New reproduction hanging rod. Fits all Coleman lamps. Approximately 11 1/2 inches long.
Reproduction lamp globe for the later style Coleman lamps. Real nice alternative to an expensive original. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Some people call this the 355 globe.
Reproduction lamp leg for the model BQ lamp. Solid brass. Comes with screw.
Used fluted lamp fount top. Looks like this fount top was painted white at one point..
Decal for the model 169K lamp.
Valve stem for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.
Decal for the model 139 lamp.
Original used Finial for Lamps
New old stock lamp finial.
New brass finial for lamps. Overall length is 1.5", but to shoulder it is 1 1/8".
From Terry Marsh's site: This wrench came with a Coleman L220 lantern dated Aug. 1928. The instructions with the lantern identify this wrench as part no. 362-950. It is 4″ long and fits nut sizes 11/16, 7/16, & 2, 5/16″ plus a 5/32″ slotted generator tip remover. This wrench also came with iron Models 4A & 609.  Link is HERE.
NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.
Burner frame for the 158, 159 and 159X kerosene lamps. May fit others too. Valve turns and seems to operate smoothly.
These are early style shade holders for the Air-o-Lite Lamps
This is a used lamp handle for the early lamps like the Model M and other Pre CQ Lamps. Some might show signs of wear. It is 4 3/4 inches long.
Burner assembly for the 158, 159 and 159X kerosene lamps. May fit others too. Valve operates well.
Can't tell if this is NOS or Used - Great Condition.
Handle ring used on the Model A Air-O-Lite and other early Lamps
This is the Bakelite top finish spacer on a CQ lamp handle. It is in used condition.
Lamp valve for 130G, 130K 130P and 131P. The bottom is threaded for a fuel and air tube to be attached.
This is a globe for the Midstate model #1200 lamp.
This is a globe for the Midstate model #1200 lamp.
This is a globe for the Midstate model #1200 lamp.
Original used green sunrise logo lamp globe. Although used it will have no defects. Logo is very lightly stamped as was common back in the old days. This globe measures 6 inches tall. The top rim opening has a 3 5/8 inch diameter. The bottom opening has a 3 1/2 inch diameter. It bulges out at the widest point to about 5 inches.
New old stock finial for lamp.
NOS burner frame and pick up tube for Lamp Models 139, 152, 152A Gasoline and Kerosene. May fit others too. Will have signs of tarnish due to age.
NOS burner frame, Valve and Generator for the 158, 159 and 159X kerosene lamps. May fit others too. Very nice condition.
this is an original used Finial for Lamps. This finial is missing the nut that threads onto the bottom.
This is a gasket sealer that many use for sealing valves to tanks. Is flexible when dry and offers good fuel resistance.
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 5ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 1/8"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 1/8"
NOS gas tip for Model A Lamps and possibly other early Torch-Lite Lamps.
Reproduction shade holder for the old CQ style lamps.
New Filter Funnel For Lamps And Stoves.
Stops filling your lantern or stove at the correct level.
Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.
