Used pump for the Sunflame Speedikook model 6906 stove.
Came in a box marked Primus parts. Looks like the outer housing for a pump. Measures 7 3/4 inches long.
These came out of the old SMP factory. This is the washer that goes behind the pump nut on an SMP military lantern.
These came out of the old SMP factory. New pump rod for the military lantern. Would also work on a 220/228B or C. Also would work on the stoves that took a longer pump such as the model 415.
These come from a Thermos fount with a standard type of pump similar to Coleman. These hold the pump cap into the fount. Will not work on Thermos lanterns where the pump screws onto the fount. Comes as a set of two.
Large leather pump cup for the T-Handle pumps, kitchen ranges, and other larger appliances. The flat portion of the cup measures 1" wide. For pump barrels with a 1 1/4 inch diameter.
Used pump for an AGM lantern. Not sure what model it is for but it measures 5 7/8 inches long.
Slightly smaller than a Coleman pump clip.
Brand new pump For the Northstar Lantern.
Fits models 2000-750T, 2000-750, 2000-750E, and 2000A750.
Very little pump only for the model 615 irons with the built in pump.
Pump plunger for the model 505. Also fits the 222 series lanterns.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
This is a complete rebuild kit for the pump on an M1950 stove. You will get the cap gasket, check valve dot, fuel tube gasket and pump leather.
This is a complete rebuild kit for the pump on an M1942 stove. You will get the cap gasket, check valve dot, and pump leather.
Stainless steel screw for the early style pumps. Fits many older models like the 242s, 243s, 247 and 249. These have the early type hard to find thread pattern. The original slotted pump screw has a more rounded head where these are flat.
This is a cap for the end of the M1950 pump. This screws into the bottom of the pump.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Small pump Leather for the model 1950 stove. Also fits the M1942 stove. Measures roughly 3/4" at it's widest point.
Smaller diameter leather pump cup for the model 427 lantern. Measures roughly 3/4" at it's widest point.
A fellow collector has shared with us that it will also fit the Akron 107 with a built on pump.
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Short pump assembly for Thermos lanterns. Pump barrel measures 3 inches. Will most likely need a new O-ring kit which are HERE.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
Reproduction small pump for the Coleman irons. Will also work on any Coleman lamp or lantern.
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Used pump for the model 530 stove. Will have a new pump leather and work just fine.
New reproduction pump cup assembly for 242 NL (No Letter), 242A , 242K, 243 , 246 and or any Coleman lantern or stove from the early 30's with a solid pump stem with no air hole in the middle. These are made for the USA manufactured Coleman pump shafts and will fit as they should. If yours is made in Canada, you will have to use a small file to widen the brass center to a cone shape to match your pump shaft - see the photos. Also known as part number 233-518
Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves.
Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201
Thermos Lantern Pump. Measures 4 7/8 inches long from end to end.
O rings for the Thermos lantern and stove pumps. One is for the pump, the other is for the top seal. These are for the later model Thermos lanterns and stoves where the pump and filler cap where combined.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the double screw holes on the plunger cap.
Pump Plunger. Fits the Peak 1 Apex Stoves 450-700, 445-700, 445-700C
Used Pump Assembly Spring
Spring ONLY
NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used brass pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather.
Has the single screw hole on the plunger cap.
This is the short pump used on the small stoves and lanterns. 400, 440 series stoves and model 222, 226, and 229 lanterns. Comes with the plastic style pump cap and neoprene pump cup. Also known as part number 400E5203
This is a new production T-handle pump. It works great to pressurize your lantern, lamp, or Handy Gas Plant. Approximately 10 inches long.
Used original old short pump for Coleman Irons. Will work on lamps and lanterns too. Pump barrel is approximately 5 1/4 inches long. This is a used pump but it will have a new pump leather and will work just fine. This is the early style pump with the wooden sleeve and screws holding the pump to the barrel.
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Used steel pump assembly for the model 242B and early 242C lanterns. Will not work on later models. It has been cleaned and will have a new pump leather. Has the double screw holes on the plunger cap.
This is a new reproduction T-handle pump. It has a dent about halfway up the barrel that catches the pump cup as you pump it (see photos).
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Neoprene pump cup and back up plate.
