- Free Shipping
Search
- Free Shipping
- Free Shipping
200A Trailblazer Red Logo Globe - G32
This is a new old stock Trailblazer globe. These are not Coleman globes but are the same size and were made in the USA about 20 to 30 years ago. Comes with the red trailblazer logo. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, 247, and 249.
- Free Shipping
Decal - Fits 1952 & 1953 200A Lanterns - D16
Yellow Border Logo Used on Coleman 200A Lanterns 1952 - 1953
- Free Shipping
Decal - Fits 1954 to 1960 200A Lanterns - D14
Yellow Border Logo Used on Coleman 200A Lanterns 1954 to 1960 "Reg."
- Free Shipping
Decal - Fits 1965 to 1971 200A, 220 & 228 F Lanterns - D12
White Border Logo with "Reg.", "Pats. Pending" & "Lantern" for1965 to 1971 200A, 220 & 228 F Lanterns. Also fits the 220G,
- Free Shipping
Decal - Fits 1951 200A & 1951 thru 1954 220 & 228E Lanterns - D17
Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns
- Free Shipping
Decal - Fits 1961 to 1964 200A, 220 & 228 E & F Lanterns - D13
No Border Logo with "Reg." & "Lantern" for 1961 to 1964 200A, 220 & 228 E & F Lanterns
- Free Shipping
Decal - Fits 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns - D11
White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.
- Free Shipping
Dark Red Decal - Fits "Some" 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns - D68
Dark Red Border Logo with "Reg.", & "Lantern". For "Some" 1971 to 1983 200A, 220, 228, 335, 236A, 237A Lanterns. This and the D11 were used interchangeably on the same lanterns/stoves. Compare with your original.
Fuel Air Tube Reproduction - R414
Reproduction shorter fuel and air tube for the double mantle Sears lanterns made by Coleman.
Needle Assembly Reproduction - S91
Reproduction needle assembly for the 200A2891 T66 generator used on models 121, 200, 200A, 202, 242, 242B, 242C, 476.72211, 476.74550
Generator Spring, Used - S98
Used generator spring for 200, 200A, 242, 243, 202 & Similar Sears Lanterns. This is the older style.
Generator Spring - R578
Reproduction generator spring for 200, 200A, 242, 243, 202 & Similar Sears Lanterns.
Pal Nut - S67
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Frame to Valve Nut - S64
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
- Free Shipping
Burner Screen - S29
This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.
Burner Frame Stainless - R350
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
- Free Shipping
Single Mantle Disk Reproduction - S01
New reproduction direction disk for the 200 & 200A USA lanterns. These are aluminum and look and feel identical to the original. These are made here in the USA. Will also fit most other lanterns. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantle" as opposed to "mantles" for a double mantle lantern.
- New!
- New!
Burner Frame, Used - U930
This is a used old style burner frame originally used on the black band 200A Lantern. Looks like someone may have replaced the tabs - they are supposed to be short.
Globe Straight No Logo - G87
This is a used unmarked straight globe that will fit many single mantle lanterns. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. This is a Fred Kuntz reproduction. Glass measures 3 1/2" Wide X 4" Tall.
- Free Shipping
Canadian Coleman Lantern Decal - D28
Coleman Decal For some Canadian Made Lanterns. Decal measures approximately 2 1/2 inches long and is one inch tall. This matches the earliest vinyl style of the decal on a few of the 200 Canadian lanterns made around 1955
Eccentric Block - S28
Eccentric Block for 200, 200A, All 242s, 201, 202, 243, 234, 335, 339 and 247. Also Sears 476.74550 & 476.72211.
Tip Cleaner Stem Reproduction - R651
Reproduction tip cleaner assembly for the model 200, 200A, 201, 202, 242, 247, 335 and similar lanterns. Also fits the 523 and the 520/M1941 stove.
Burner Cap Reproduction - S34
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
- Free Shipping
U Tube Newer Style With Venturi Used - E1486
This is a used newer style U tube with Venturi. These are used.
- New!
Kamplite-AGM Globe - G209
This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.
1/4" Valve Stem Bushing - S137
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
Reproduction Gas Tip - GT2
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
Pump Screw, Used - S108
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
- New!
440 Mica Globe - G12
This is a reproduction mica globe for the smaller single mantle lanterns. This will fit on the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns. It will also fit on any lantern that would take a 440 size globe. It is 4 1/4 inches tall and has a diameter of 3 1/2 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
Valve Assembly, Used - E1356
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Pump Screw - S70
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Generator, 286/288 - C007
This is a new Coleman made generator for lantern models 200B, 286 & 288. Generator includes new gas tip, spring, and tip cleaning wire.
This part is also known as part number 3000005403.Valve Assembly, Used - E1642
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Spring Clip (Preheater Cup) - R579
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
Generator Tube Packing - P05
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
Generator Tube Packing - 🟡𝟭𝟬 𝗣𝗔𝗖𝗞 - P05
This is a 10 PACK of the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
Valve Wheel Black Old Style, Used - S113
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.