Direction Disk, Small - E1629
NOS Direction disk. Small disk with little less than a 3/4 inch diameter. Mostly used on propane stoves - will be way too small for a GPA lantern or stove.
NOS Direction disk. Small disk with little less than a 3/4 inch diameter. Mostly used on propane stoves - will be way too small for a GPA lantern or stove.
Gas tip for the 339 generator. These are for the newer generators, not the old original ones. Overall length is 7/16", thread width is 5/32" and head width is 13/64". If yours is much smaller, it will not fit. Below is a photo of an old type on the right, and the new one we have in stock on the left.
Generator Coil For generator 940-262. Measures 9 1/8 inches long and has a diameter of about 1/4 inch.
Gas tip.
Used on Coleman Air-O-Gas Range No. 322 and Coleman Air-O-Gas Stoves Nos. 329, 600, 601, 602, 620, 621, 622, 623, 624, 625, Coleman Cooker Range Nos. 17, 17-0, 17-10, 18, 18-0, 18-10, 364, 364A, 366 and Coleman Cooker Stove Nos. 12, 12-3, 86, 86-4, 360, 361, 363, 365.
Feed Tube Assembly for the 214 Lanterns.
Also known as part number 2145231ZCL.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
Used direction disk for some propane stoves. Small disk with little less than a 3/4 inch diameter.
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
Used top half of the burner assembly for a slant lantern or lamp.
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.
Amber globe for the 288 size lantern. Has no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.
It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This original globe fits models 214, 214A, 214B, 214C, 282, 282A, 288, 288A, 288B, 286, 286A, 286B, 321, 335, 5150, 5151, 5152, 5153, 5154, 5155, 5158, 5159, and 5417. Made in the USA. This globe is used.
Picket amber globe for the 288 size lantern. Has no manufacturer markings on it anywhere. It is approximately 4 3/8 inches tall and has a 4 1/4 inch diameter. This globe fits models 214, 214A, 214B, 214C, 282, 282A, 285, 288, 288A, 288B, 286, 286A, 286B, 321,325, 335, 5150, 5151 (A/B/C/D), 5154 (A/B), 5155 (A/B), 5159, 5417, 5419, 5428, & 5429.
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Used Part that Fits models 214, 220K, 228K, 282, 285, 286, 288, 290, & 295 lanterns.
Will all vary in wear and some may have rust .
Same as part number 288-1251
This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.