220/228 Valve Bushing Set - S134
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
German made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.
Used Eccentric Block for the 220 & 228 lanterns up through model F. Will not fit H, J, or K.
USA made white logo globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.
This product is not included in the OCP free shipping program.
Photo's with lanterns are for illustration purposes only.
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is a used Century Primus globe 8936 made by Schott Suprax Glas made in West Germany. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Has a spot that looks glued or burnt on (see photos)
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
This is the decal used on the early painted 220D/228D transitional lantern.
This is an original used green sunrise logo globe made between 1946 and 1959. Although used, it has been inspected for damage or defects.
The light green logo is very light as was common. The back has "PYREX" over "MADE IN USA"
This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. Some of the markings are very light and hard to see.
This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.
Fount dated 5-77 for the model 220/228 Lanterns, models H thru K. This fount has some scratches, paint chipping, and rust - see photos.
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-65.
Has paint chipping and a couple scratches/scuffs (see photos)
Fount dated 12-80. For models 220/228 H thru K. Has some scuffs/scratches and paint chipping on the bottom of the fount (see photos).
Made in USA 220 white logo replacement.
This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
This is a used fount for the 220/228K lantern dated 5-73. It has a couple paint chips and some writing on the bottom of the tank, otherwise it is in good shape.
It will work for any 220/228H through 220K type models.
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62.
Has paint chipping and some rust (see photos)
Direction disk for the 220H, 220J and 220K lanterns. New old stock from an old parts bin at a repair location.
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
This is a used old style fount for the 220/228B through 220/228F lanterns.
Has small scratches/scuffs, chips and looks like some plastic got melted to the outside but might be able to get it off (see photos).
Coleman Lantern Logo for 1955 to 1961 220 & 228 E Lanterns
Instruction Decal for 1945 to 1946 220C & 228C Lanterns. Also fits some 220D & 228D Lanterns
White Border Logo with "Reg.", "Pats. Pending" & "Lantern" for1965 to 1971 200A, 220 & 228 F Lanterns. Also fits the 220G,
Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns
No Border Logo with "Reg." & "Lantern" for 1961 to 1964 200A, 220 & 228 E & F Lanterns
White Border Logo with "Reg.", & "Lantern". For 1971 to 1983 200A, 220 & 228 F, H, & K Lanterns. Also fits 502 stove and the 335, 236A, 237A Lanterns.
Dark Red Border Logo with "Reg.", & "Lantern". For "Some" 1971 to 1983 200A, 220, 228, 335, 236A, 237A Lanterns. This and the D11 were used interchangeably on the same lanterns/stoves. Compare with your original.
Reproduction eccentric block for the very early 220B lantern that took the longer eccentric. Will not work in the later 220B or other 220 series lantern.
Reproduction check valve for the military lanterns. Will also fit the models 220/228B and 220/228C. Will not fit the later style lanterns.
Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
Used Sears small hat ventilator. Will also work on the model 220 lantern. This one has some paint chipping and a dent (see photos)
This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.
Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.
New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
New reproduction direction disk for the many of the 2 mantle lanterns made in the USA like the 220 and 228 models B thru F. These are aluminum and look and feel identical to the original, and they are made here in the USA. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantles" as opposed to "mantle" for a single mantle lantern.
Used direction disk for the earlier double mantle lanterns such as 220/228B, C, D, E, and F. Will show signs of wear but still be in good condition. May be a transition disk between the 70's & 80's model lanterns.