Burner ring for Thermos stoves. May show signs of light rust.
Burner tube for the model 339 lantern.
Burner assembly for the model 5151 propane lantern.
Burner tube for the model 249 lantern.
Burner for the model 522 military stove.
Burner fillers for the 940-365 master burner.
Burner fillers for the model 3F stove.
Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Burner frame for the 158, 159 and 159X kerosene lamps. May fit others too. Valve turns and seems to operate smoothly.
NOS burner frame for the model 222 Peak 1 Lantern
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves
HYAK diverter for Coleman 3 burner stoves.
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
Used burner support for the 502 stove. Will have varying rust on each one but all are solid.
Burner assembly with brass burner tubes
Burner tube for the 201 kerosene lantern. Has a larger opening on the end than the 200 burner tube.
Burner assembly. for the 5154A Lantern
Burner assembly for the rare 414 gas stove with electronic ignition.
Used burner bowl for the 502 stove. These are in good shape and may have some rust. The photo is an example, not the actual.
Burner ring set for the model 396 and 397 master burner.
Burner ring set used on the 952 range
Used Burner Assembly for the model 288A lanterns.
New, reproduction burner cap for 321, 331, 335, 339, 621, 625, 635 and 639 lanterns. Solid brass with stainless steel screen.
Also known as part number 335-315
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
Used burner bowl for the 502 stove. Rusty, but seems solid. Each one will vary with the amount of rust.
Screw/Bolt for the burners on 5435A and 5435B Stoves. 2 are needed for both stoves.
Burner Tube for 321, 331, 335, 339, and 625 Lanterns
Used burner assembly for lantern models 5154B, 5152D, 5153A, 5151C and 5150. Burner screens are in good shape.
NOS burner frame and pick up tube for Lamp Models 139, 152, 152A Gasoline and Kerosene. May fit others too. Will have signs of tarnish due to age.
New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
Fits models 290, 290A, 290B and 295, 295A.
Burner assembly for the model 288 lanterns. The burner tubes are brass.
This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242 and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.
Burner Assembly for the model 288 lanterns. The burner tubes are steel. Will vary in wear.
Brass burner tube for the 214 lanterns.
1/2 inch long screw for the 500 stove. Requires two for the Cap and Fillers. See description tab for more details.
Burner tube for the Canadian model 200 lantern. It is 1 5/8 inches long which is a little shorter than the US 200A burner tube.
Used burner assembly for the model 295 lantern.
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
Steel burner tube for the 214 lantern.
This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.
New burner cap & screen for the model 236, 237 and 249 lanterns.
Solid brass with stainless steel screen.
Burner support screw for a 502 stove. Each stove requires 3 total.
