Search
- New!
Ventilator 339, Used - F150
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.
Sears Valve Wheel Star, Used - E1623
Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.
Air Tube Screw - S72
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Ball Nut, 2 Pack - C011
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.Coleman Filter Funnel - C024
New Filter Funnel For Lamps And Stoves.
Stops filling your lantern or stove at the correct level.
Valve Wheel Screw - S60
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
Valve Wheel Black, Old Style, NOS - E1679
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
Burner Tube Short/Slant - S135
Shorter burner tube for the model 220 slant lantern. Same as the normal 101-324 burner tube only a little shorter. Measures 2 1/4 inches long. Many of the slant 220 and 228 lanterns took shorter burner tubes.
Valve Stem - E1228
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
Air Stem Old Style Long Used - E1613
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Air Stem, Old Style, Long, Reproduction - R582
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Tip Cleaner Stem Packing - S129
These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.
Valve Wheel Black Old Style, Used - S113
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
Air Stem, Old Style, Used - S107
Air stem older style used. Has the larger head on the end.
In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A
Peerless Mantles 24-A - M04
These Peerless mantles work well on single mantle lanterns. Made in India. They are the same size as the Coleman 99 mantles. A little bigger than the 2C-HG mantles but not as big as the 111 mantles. 2 per pack.
Check Valve Old Style - R425
Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
Pump Screw - S70
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Generator Nut, Used - S105
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
Jamb Nut, NOS - E1627
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
Generator Nut, Reproduction - S124
Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.
Burner Tube Brass 2 7/8 - E1254
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Burner Tube 2 1/2 Inch - E1471
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
Burner Tube Brass 2 3/4 - E1129
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
Fuel Tip - E1195
Fuel tip used on the end of the fuel tubes of early 220/228B lanterns, 236 and some lamps.
Pump Assembly, 220C Thick Steel Cap, Used - E1296
This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.
Check Valve Old Style Reproduction - R577
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
Burner Assembly Complete, Round, Used - U830
This is a used burner assembly with the round mixing chamber that will fit the model 220F & 228F. It will be in fine working condition. It may show signs of tarnish and other spots from being old.
Burner Cap 220 Brass Round, NOS - E1044
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
Mantles, Insta-Clip #21, 2 pack - M12
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack.Â
These simply slide on and you cross the wires instead of tying strings - very quick to install.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Mantle Insta-Clip 2 #21 2 pack - M13
Coleman's Most Popular Sized Mantles with the Insta-Clip. 2 mantles per pack. Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Burner Tube Steel Old Style - E1101
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
Mica Globe Panels - E1120
These mica panels are 3" x 5" in size.
General information:
- Mica can be cut with sharp scissors or a good paper cutter
- This is the only size that is available
- Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
- Mica is not available in amber or red.
- Mica can withstand temperatures up to 1800 degrees F.
- These are only sold in a package of 5 panels.
- Free Shipping
252 Direction Disk - S10
Direction disk for the military lanterns. These came out of the old SMP factory.
- New!
Eccentric Block - E1039
New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.
Pump Assembly Plastic Cap, Used - E1426
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
- 3% less
Pump Assembly Neoprene Fixed End, Used - E1420
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Ball Nut, Used - S101
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Pump Assembly, Universal - C006
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.Graphite Ribbon - P09
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.