Search

Pump Clip

Used pump clip that fits most lanterns and stoves. It is used but in fine shape.

This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.

HERE is a new filler cap screw if needed.

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.

Small thin O ring for the common Coleman check valves. Made of gas resistant material.

This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.

C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.  
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves. 

This is a new, reproduction 3 piece cap. Excellent craftsmanship. This is not the type with a hole in the side.

This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps. 

It is also known as part number 425A1405.

This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.

This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.

This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.

Comes with a new gasket that you will have to install.

This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.

This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.

Used steel filler cap for Coleman lanterns. All will vary in wear.

Comes with a new gasket that you will have to install.

Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.

Wear and finish will vary. 

Comes with a new gasket that you will have to install.

This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.

Used nickel plated one piece cap. All will vary in wear.

Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.  

Comes with a new gasket that you will have to install.

This is a used one piece brass filler cap. Wear will vary. 

Comes with a new gasket that you will have to install.

This is the common Coleman pump cup that fits most lanterns and stoves. 

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top.  Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.

Brand new pump For the Northstar Lantern. 

Fits models 2000-750T, 2000-750, 2000-750E, and 2000A750.

Leveling ring.

Filler Cap For Northstar Lantern - 2000-750T 2000-750 2000-750E 2000A750. New part number 3000005380. 

Comes with a new gasket that you may need to install.

Ei Module For Northstar 2000A Lantern

Generator For Northstar Lantern 2000-750T 2000-750 2000-750E 2000A750. New generator includes new gas tip, spring, and tip cleaning wire.

Also known as part number 3000005096.

Valve assembly for Northstar Lantern.

Check valve for the Northstar lantern.

Generator Needle For Northstar Lantern 2000-750T 2000-750 2000-750E 2000A750. This is a reproduction part.

Cooler ice tray - have some yellowing from age. 13" long and 10" wide. These are solid and have no holes or cracks.

Fits models: 5254D, E F, 5255D, E, F, 5256D, E, and F

Used ice tub for the older steel belted coolers. 10.3/4" tall, 10" wide 13" long. No cracks or holes. Good shape.

Fits models: 5254D, E F, 5255D, E, F, 5256D, E, and F

New cooler tray. This tray measures approximately 9" X 11-9/16" and is 2-3/4 inches deep. Has some yellowing from age but is in good shape with no cracks or holes.

These fit in cooler models: 5252, 5253,  5252B, 5252C, 5253A, 5279, 5280, 5280A, 5285, 5285A, 5285B, 5283A, 5284, 5284A, 5284B, 5281, 5282

Used freezer pack for large coolers. Fll it with water, freeze it, and then put it in your cooler to help keep it cold. Afterward, use it for a water jug when the ice melts. Has a few stains on the outside but is good shape. It is 13 inches long and 7 3/4 inches high. Has a thickness of 3 1/2 inches.

Used freezer pack for large coolers. Fll it with water, freeze it, and then put it in your cooler to help keep it cold. Afterward, use it for a water jug when the ice melts. Has a few stains on the outside but is good shape. It is 13 inches long and 7 3/4 inches high. Has a thickness of 3 1/2 inches.

Mantles for 2000 and 2500 series lanterns. 

Also known as part number 2000026606.

Coleman Insta Clip # 95 Mantles 2-Pack for the Northstar lantern.

Also known as part number 2000026606.

Vent nut for the Northstar lantern.

This is a new Coleman made generator for lantern models 282 and 285. Includes a new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005622.

Coleman #51 Mantles. 2 per pack Fits models 3018, 3023, 3112, 5130, 5132, 5133, 5134, 5136, and 9742

Also known as part number 2000026608.

Steel Cam Latch and screws. Fits Steel Belted Coolers made in the year 2000 and newer. Will not work on the older ones. For models 6150, 6154, 6154B, 6155 and 6155B.

Also known as part number 5010005238.