Bail Handle Reproduction - R311
This is a very nice reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns. Made of spring steel here in the USA.
This is a very nice reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns. Made of spring steel here in the USA.
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".
Used short style vent for the 200/200A lanterns made in 1963 and after.
This vent has some scratches/scuffs and paint chippings (shown in photos)
Reproduction bail handle for the model 200, 200A, 200B, 201, and 202 lanterns.
These bail handles are new but are not straight (shown in photos) - they can be fixed with some patience and a propane torch.
Used red carry case for lanterns. Fits models 200, 200A, 200B, 201, 202, 288, 286, 321B, 335 and other smaller sized lanterns.
Has some scratches and a dent on the top (see photos)
This is a new, Coleman made generator for Model 214 and 214A Coleman Lanterns. Each includes new gas tip, spring, and tip cleaning wire.
These are also known as part number 3000005092.
Reproduction generator for the AGM model LRL21, LRL21A, LRL22, KL2, and JC Higgins model 710.7400, 710.74001 lanterns. Part number on JC Higgins parts diagram is 7110 - Generator Assembly
This is a new, Coleman made generator for Model 214 and 214A Coleman Lanterns. Each includes new gas tip, spring, and tip cleaning wire.
These are also known as part number 3000005092.
New reproduction vent rod for the 200A. This is the longer vent rod made for lanterns 1963 and earlier.
This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a new gasket for your metal snap on parts safe. Fits the 200A size metal safe. Measures 5 1/4" from outside edge to outside edge of gasket.
Feed Tube Assembly for the 214 Lanterns.
Also known as part number 2145231ZCL.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Reproduction valve stem for the model 200A lantern. Comes with a new valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Used valve stem for the model 200A lantern. Has been cleaned, and packing changed.
This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
Used short style vent for 200/200A lanterns. This vent has some paint chipping (see photos)
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
Used short style vent for the 200/200A lanterns. Has a some scratches/scuffs and paint chips (see photos).
Used tall style vent for the 200/200A lanterns.
This one has some scratches and paint chipping (see photos)
This is a used tall style vent for the 200 and 200A Lantern.
Has some paint chips (see photos)
Reproduction gas tip for 200A5891 generator. Also works well for using on the 220 generators to do a kerosene conversion.
Used tall style vent for 200/200A lanterns made in 1962 and before. This vent has some rust and chippings (see photos).
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Used spring for the fuel tube spring on the model 200, 200A, 202 and 242 series lanterns. Also for the 530 pocket stove.
This is a used collar for the model 200A lantern.
It may show signs of wear/scratches. Each collar may slightly vary in wear.
This is a used fount for the 200A lantern dated 6-76. This fount as a couple paint chipping/scuffs, overall great condition (see photos)
Reproduction 200A Vent Rod Bracket Short. Made to fit the 1963 and later 200A's with the lower profile vent.
New reproduction direction disk for the 200 & 200A USA lanterns. These are aluminum and look and feel identical to the original. These are made here in the USA. Will also fit most other lanterns. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantle" as opposed to "mantles" for a double mantle lantern.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.