4-36 x 5/16 Brass Screw - S61
This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..
This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..
Replacement decals for All Military Lanterns ~ Set of Three Decals
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
Reproduction generator nut for the 252 military lantern. Made of brass.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Used ball nut for the model 275 lantern. This is the checkered variety.
NOS Military Lantern globe channel. Crimps on burner frame to hold quadrant globe panes.
Original NOS generator nut for the Milspec lantern. Military part number 6260-00-161-1859
New Old Stock - Parts well cap for the military lantern. Has a new rubber gasket.
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
Used generator spring for 200, 220, 228, 242, and 275 lanterns. Also fits some Sears models. This is the newer style.
Will show signs of use but will be in good shape.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
Reproduction fuel tube for the model 200, 202 and 242 series lanterns. Also fits the 530 stove.
Used collar for the milspec lantern. They have a few small spots of missing paint here and there.
This used block if for the 275A lantern. Not sure of compatibility with the 275.
Used Canadian 242B collar with small writing.
Each will vary in amount of wear and discoloration.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
This is a used steel collar for the model 242C lantern. Has a good amount of rust.
Brass bolt for 242 or 242NL Lantern - will not fit other versions of the 242. This is just for the top brass bolt.
Generator tip cleaning tool for the military lantern - This tool is missing the pricker rod on one side of the tool.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.
This is a used steel collar for the model 242C lantern. Will vary in amount of rust and wear.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a used collar for the model 242B lantern. It may have spots of rust or other discoloration/ stains.
Reproduction Generator for the Model 249 Lantern. Generator includes gas tip, spring, and tip cleaning wire. Made in the USA.
New steel fuel tube spring for the models 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 3/16" and an ID of approximately 1/8".
Brass Vent Bolt for 243B, and all 241 Lanterns - this bolts down into the top of the frame to hold the vent.