Search

Original one piece decals for the later SMP military lanterns. These are not reproductions. They came from the old stock of the factory when it closed.

This is a used collar for the model 242B "Sport-Lite" lantern. It may have spots of rust or other discoloration/ stains.

Original used pre-heater cup for the model 234 lantern. Also would be correct for the Canadian model 247 lantern.

Reproduction spring for the fuel tube spring on the model 200, 200A, 202, 220 series, 228 series, and 242 series lanterns. Also for the 530 pocket stove and most likely many others. Overall measures 9/16" long, OD of 5/32" and an ID of approximately 1/8".

Used Smith-Victor carry case for all large hat 228 style lanterns. Will also fit 220, 252, 275, 290, and 295. 

Has some scratches, one edge is bent a little but doesn't hinder the case closing, both latches aren't perfect on latches tight but is a little bent, the other latch is loose but still closes.

This product is not included in the OCP free shipping program.

Direction disk for the military lanterns. These came out of the old SMP factory.

This is a new old stock generator.

Fits Military model 252 lantern. Also other non Coleman military lanterns

New burner cap & screen for the model 236, 237 and 249 lanterns. 

Solid brass with stainless steel screen.

This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.

Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.

New Generator for 201, 241 and 247 Kerosene Lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 242K289, 201B5891 and 3000005402.

Used clear quadrant glass pane for the milspec lantern. They are in excellent condition with no cracks. On some of them edges are slightly chipped as was common on these. The chipping is covered by the globe channels. They measure approximately 3 3/8 inches wide and 5 1/4 inches high.

New burner screen for the models 236, 237 and 249.

Valve stem nut for the model 214, 242 and 200 series lanterns.

This is the small part that attaches to the filler cap screw so you can hook the chain to it.

This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.

These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.

Rebuild kit for both the 275 and 275A lanterns. Cures most troubles.

Includes:

• 4 Peerless string tie mantles for the 275 or 275A lantern
• 1 Reproduction Generator for the 275 or 275A lantern
• 1 Leather replacement pump cup for the bottom of the thumb operated air pump
• 1 Valve Stem Packing for sealing fuel leaks around the fuel valve
• 1 Cap Gasket - for your fuel cap.

See Diagram in "Description" under photo at bottom left of this page

More parts for: 

• 275 HERE
• 275A HERE

Reproduction check valve for the military lanterns. Will also fit the models 220/228B and 220/228C. Will not fit the later style lanterns.

Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel. 

We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.

A graphite valve stem packing is included with each of these in case you end up needing to change them.

This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.

Used valve stem nut for many Coleman lanterns.

This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.

Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".

Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.

Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.

Brass Pin for 242 or 242NL Lantern - will not fit other versions of the 242. This is secured directly to the 242 vent. This fits into the burner frame hole - It forms to the 242 vent and captures it permanently after you heat it and swedge it in place. See directions below. Comes with Steel rod to assist in the process.

Installing Pin into a 242 vent:

1. Position the steel shaft with the hole end up in a vise securely. 
2. Put the brass pin insert in the hole of the big shaft. 
3. Heat the small lip of the brass insert with a propane torch until it's a nice orange color, this will anneal it and make the brass softer so it won't crack when it's tapped over. 
4. Set the vent over the insert. 
5. Place a ball peen hammer or something with a similar on the heated lip of the pin.
6. Tap down with a hammer onto the center and gently tap it with another hammer to swedge it outward - continue until it's seated nicely in the vent.

You will notice the edges of the lip will fall away.

Round steel burner cap for most models of double mantle lanterns and lamps.

Air stem older style used. Has the larger head on the end.

In the 426 stove series, this only fits 426B and C stoves, not 426 or 426A

New reproduction eccentric Block for the 275, 235, 220/228 C, D, E and F models in addition to some lamps.

New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.

Reproduction 7/16" generator wrenches. These are the wrenches used for the smaller generators. Great for putting in your part safe.

Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.

Used Gas tip.

Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.

Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.

Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.

NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit.  No other sizes of chain are currently available that are an exact match to what was used.

Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.

Solid brass with stainless steel screen.

Same part number as 112-323

N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.

This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.

Also known as part number 3000005094.

NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.

This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. 

If your filler cap is a standard size and has a bolt in the center then these gaskets will work. 

Red 3 piece filler cap shown for demonstration purposes only.

This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.  If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Used air stem for most post-1980 stoves and lanterns. Has the smaller end on the air stem.

This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Used valve wheel screw.  Will be in good condition.

Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.