- New!
222/226/229 Generator Needle - S127
New Reproduction Generator Needle for Model 222, 222A, 222B, 226 and the 229.
New Reproduction Generator Needle for Model 222, 222A, 222B, 226 and the 229.
These mica panels are 3" x 5" in size.
General information:
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap off the Model 200A burgundy.
Comes with a new gasket that you will have to install.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
String Tie Mantles for Models 222, 226, 229, and 3022 lanterns
Also known as part number 3000004346.
Used filler cap with lanyard for the small backpacking lanterns - in very nice shape. Will also fit most other lantern and stoves that use the standard size filler cap. Comes with a new gasket that you will have to install.
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
NOS gas tip for Model A Lamps and possibly other early Torch-Lite Lamps.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
Used pump assembly with fixed end, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
New Reproduction Generator for Model 222, 222A, 222B and the 229. Generator includes new gas tip, spring, and tip cleaning wire.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7
It has been reported that the 285 valve stem uses 2 of these.
Used nickel plated one piece cap. All will vary in wear.
Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Comes with a new gasket that you will have to install.
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #5
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
Mica globe for the small backpacking lanterns. Will fit models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
Would be good for camping as it will not break like glass.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is a 10 PACK of the cardboard tube that goes inside of the 200A and 220 size generators, and many others.