- New!
Mixing Chamber Earlier Style, Used - E1636
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
Used top half of the burner assembly for a slant lantern or lamp.
Nickel Tip Cleaner Assembly with air piece. Does not have the eccentric block.
Fuel and air tube for lantern models 220/228B, 220BX, and 220/228C. Earliest style of fuel and air tube.
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
Used guillotine carry case for all large hat 228 style lanterns. Will also fit 220, 275, 290, and 295.
Latch works great - has some scratches and a couple small dents - overall great condition (see photos)
This product is not included in the OCP free shipping program.
Used Smith-Victor carry case for all large hat 228 style lanterns. Will also fit 220, 252, 275, 290, and 295.
Has some scratches, one edge is bent a little but doesn't hinder the case closing, both latches aren't perfect on latches tight but is a little bent, the other latch is loose but still closes.
This product is not included in the OCP free shipping program.
This is an original 220 Coleman vent. The black porcelain finish was custom done by Independence Porcelain Enamel (IPE). This is for the late 220F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
This is a used but newly re-done guillotine carry case. It does not have the decal, latches or rivets needed to put it together.
This product is not included in the OCP free shipping program.
This is a used but newly re-done guillotine carry case. It does not have the decal, latches or rivets needed to put it together.
This is a used but newly re-done guillotine carry case. It does not have the decal, latches or rivets needed to put it together. This one has a couple scratches from being moved around from place to place.
This product is not included in the OCP free shipping program.
Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
This ventilator is used. It will fit Canadian models 339, 335, 321A, 321B, 321C, 325, and 325A.
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
This is a used fount for the 220/228K lantern dated 5-73. It has a couple paint chips and some writing on the bottom of the tank, otherwise it is in good shape.
It will work for any 220/228H through 220K type models.
This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62.
Has paint chipping and some rust (see photos)
New frosted Batman globe. This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Also known as part number 2000026613.
Used direction disk for the 220/228H lantern. Will show signs of wear but still be in good condition.
This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.
This is an original used globe for the Coleman made Sears lanterns made from 1963 to approximately 1970. Although used, it has been inspected for damage or defects. This globe will fit models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
This is a US made original globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches. These are used globes but in very nice shape.
Made in USA 220 white logo replacement.
This globe fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
This is a Peerless Japan made globe for models 220, 228, 290, 290A, 295 and 235. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
Used no letter globe. This fits the model 220, 290, 228, 235, and 295. This globe measures approximately 5 1/4 inch high and has a diameter of approximately 4 7/8 inches.
This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
These are reproduction packings for the tip cleaner stems on many models to include these: 200, 200A, 202, 220/228, 236, 237, 242 lanterns and also many stoves. To install this packing, the lever must be straightened out, which can be difficult.
These mica panels are 3" x 5" in size.
General information:
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
This is a used older style brass mixing chamber for the 220-228 series lanterns.
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
This is a used old style fount for the 220/228B through 220/228F lanterns.
Has small scratches/scuffs, chips and looks like some plastic got melted to the outside but might be able to get it off (see photos).
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.