This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many. Comes with a new gasket that you will have to install.
Used carry case for the M1950 stove. Can also be used for other military stoves such as the 520. Will not fit the 530. Has a couple dents and scratches (see photos)
This is a new reproduction T-handle pump. It has a dent about halfway up the barrel that catches the pump cup as you pump it (see photos).
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Used combo pre-heater cup and gen nut for the M1950 stove.
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
Used brass filler cap. Will all vary in wear and amount of brass faded. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Will come with a new gasket for you to install if needed.
This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Comes with a new gasket for you to installed if needed.
"Butterfly" mantle No 41. 500-600 C.P. Suitable for 500 candlepower lanterns such as model 236 and 237. 1 mantle per pack.
Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
This is a cap for the end of the M1950 pump. This screws into the bottom of the pump.
This is a used pip holder cup for the M1950 stove pump. Comes with a new rubber pip.
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Decal for the Aladdin made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
Decal for the Coleman made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
M-1942 Mod Tip Cleaner Graphite packing for all companies who manufactured the stove.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
This is a used one piece filler cap from a 275 lantern. Paint may be chipped or missing in some spots - wear will vary. Comes with a new gasket that you will have to install.
New Old Stock parts. Comes with original box.
This is a used old copper funnel. Smaller spout end fits the model 242 series lanterns and 500 stoves well.
Rebuild kit for the 500 & 500A stove. Kit includes a new reproduction generator, valve stem packing, leather pump cup, and a new fuel cap gasket (stove came with one of two types - each is included).
If you need other parts for your stove, click HERE.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Bracket screw for the model 500 and 500A stove - Screw ONLY.
If you need just the bracket it is HERE.
Reproduction generator needle for the model 500 and for the 345 kerosene marine stove.
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
This is a reproduction brass cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
This tool has both a wide and slim slot for almost all check valves and makes changing check valves very easy - will only take a few minutes if used properly.
C001 Check Valve: This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date.
R425 Check Valve: This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.
NOS, HGP cap. Fits models 457, 457G, 575, 460, 470G Handy Gas Plants. Also fits the 465 Tank.
Used collar for the model 500A stove.
Decal for the Preway made M1942 MOD military stove. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
These are original style waterslide decals. Design taken from a M1950 stove built in 1972, but may fit other years.
Click on the "Description" under the photo to see the waterslide installation instructions.
These are original style waterslide decals. Design taken from a M1950 stove built in 1951 by Coleman with a silver label, but may fit other years.
Click on the "Description" under the photo to see the waterslide installation instructions.
These are original style waterslide decals. Design taken from a M1950 stove built in 1951 by Coleman with a gold label, but may fit other years.
Click on the "Description" under the photo to see the waterslide installation instructions.
These are original style waterslide decals. Design taken from a M1950 stove built in 1951& 52 by Rogers, with a silver label, but may fit other years.
Click on the "Description" under the photo to see the waterslide installation instructions.
These are original style waterslide decals. Design taken from a M1950 stove built in 1951& 52 by Rogers, with a gold label, but may fit other years.
Click on the "Description" under the photo to see the waterslide installation instructions.
These are original style waterslide decals. Design taken from a M1950 stove built in 1963 by Rogers with a gold label, but may fit other years.
Click on the "Description" under the photo to see the waterslide installation instructions.
These are original style waterslide decals. Design taken from a M1950 stove built in 1963 by Rogers with a Silver label, but may fit other years.
Click on the "Description" under the photo to see the waterslide installation instructions.
