Used pump for an AGM lantern. Not sure what model it is for but it measures 5 7/8 inches long.
Valve for the hollow wire system. Possibly for AGM.
Unknown AGM valve stem. Measures 2 1/4 inches long.
New old stock AGM valve stem. Measures 2 1/8 inches long.
Used generator for the model 8326 Thermos lantern. These fit also the Wards/Western Field Model 60-9523 and some AGM lanterns that use part number S7706.
These generators come in different conditions - all show wear and signs of use. The pricker rods are good in each and move freely.
Generator for AGM lanterns. Measures 3 1/8 inches long. Fits the AGM model 3025 lantern. Thanks to Joe P. for this information.
Generator for an AGM lantern. Measures 3 9/16 inches long.
This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.
Generator for some model of AGM lantern. Measures only 1 9/16 inches long.
Generator for some model of AGM lantern. Measures only 1 9/16 inches long. Missing the tip cleaning needle.
Used AGM Cap. Has a steel screw and new filler cap gasket. This filler cap has the AGM hole in top. Shows signs of wear. Could be any combination of the following; wrench marks, oxidization, or fading.
Burner cap. Similar in size to the Coleman 220 burner cap.
This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.
This is a reproduction tip cleaner stem for the model 220/228B through 220/228F lantern. Looks a little different that the original but is a great lower cost alternative to the original ones.
This also fits the AGM 2572 & Kamplite RL-3
Reproduction generator for the AGM model LRL21, LRL21A, LRL22, KL2, and JC Higgins model 710.7400, 710.74001 lanterns. Part number on JC Higgins parts diagram is 7110 - Generator Assembly
Decal for the AGM model 3016 Lantern. This decal is the waterslide type - not peel and stick.
Click on the "Description" under the photo to see the installation instructions.
Cut off valve. I believe this is for the K fuel stoves but am not sure.
This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.
Unknown screen. Measures 1/2 inch in diameter. Very fine brass. Seems too fine to be for a burner screen. Came out of a lot of old AGM parts.
Used burner frame for the model 2572 lantern.
I believe these generators are for an AGM iron. They measure 4 inches long.
This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.
I believe these are burner tubes for an AGM double mantle lantern. They are 2 7/8 inches long. Roughly the same diameter as Coleman burner tubes. Made of steel.
This is a used burner frame for the AGM 2572 lantern.
Burner ring measures 2 7/8 inches diameter.
Eccentric block for AGM lanterns. Measures 15/16 of an inch long.
Burner plate. Has a 2 1/2 inch diameter.
Screen retainer. Has an approximate diameter of 7/8 of an inch.
