- New!
- May 1, 2024Gather 'round, fellow GPA enthusiasts!Our annual convention is fast approaching, and guess what? It’s practically in our backyard—just 40 miles from our OCP home! June 27 to 29, 2024
NOS Burner Cap for the early stove models 2, 9, 2C, 9C, 2E, 9E, 2F, and 9F
Cannot be used on the Model 1.
Wood handle for the blue Coleman irons. Was also used on the 242 reflectors.
These are NOS iron filler caps that are nickel plated. They are a bit dusty from rolling around on a shelf, but should clean up nicely. Fits most irons and other appliances that take a small filler cap.
Used original old short pump for Coleman Irons. Will work on lamps and lanterns too. Pump barrel is approximately 5 1/4 inches long. This is a used pump but it will have a new pump leather and will work just fine. This is the early style pump with the wooden sleeve and screws holding the pump to the barrel.
Handle bolt for Coleman irons. Also used on the old wood handle lantern reflectors.
Supply is limited to what is left over from previous years. Heavy duty embroidered patch with iron on backing. Measures 3 inches diameter.
Small 4" x 4" Stainless steel cast iron cleaner for grills, BBQ's, and cookware. Good size to take camping.
From Terry Marsh's site: This wrench came with a Coleman L220 lantern dated Aug. 1928. The instructions with the lantern identify this wrench as part no. 362-950. It is 4″ long and fits nut sizes 11/16, 7/16, & 2, 5/16″ plus a 5/32″ slotted generator tip remover. This wrench also came with iron Models 4A & 609. Link is HERE.
Reproduction small pump for the Coleman irons. Will also work on any Coleman lamp or lantern.
Reproduction iron filler cap. Fits most irons and other appliances that take a small filler cap.
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Supply is limited to what is left over from previous years. Heavy duty embroidered patch with iron on backing. Measures approximately 3 inches diameter.
Valve body for irons. The upright piece is 1 1/4 inches long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Handle for the Tilley model DN 250 and DN 250A iron. New old stock but may have some scratches from storage over the years.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
This is a valve stem for a Canadian iron, but we do not know the part number or which models it fits. The length of the entire shaft from the base of the handle to the tip is 1/5". The valve stem has been drilled out and can accept a rod.
I believe these generators are for an AGM iron. They measure 4 inches long.
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. The upright piece has a screen in the end of it. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Original slot cleaning tool for Coleman irons. New old stock but will show signs of rust and tarnish.