- New!
- May 1, 2024Gather 'round, fellow GPA enthusiasts!Our annual convention is fast approaching, and guess what? It’s practically in our backyard—just 40 miles from our OCP home! June 27 to 29, 2024
Unknown NOS valve stem with fiber wheel. Stem measures 1 1/4 inches.
Does not come with packing or valve stem nut.
Unknown NOS valve stem with fiber wheel. Stem measures 1 1/4 inches.
Used maroon valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves. Completely interchangeable with valve wheel 425-1491.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.
Valve stem that I can't identify. Has a pointed end. It is 1 3/4 inches long. Has a smaller diameter shaft that would take the small packing. The valve stem nut is for a 7/16 wrench. Has a solid formed wheel that is not held on with a screw.
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
NOS valve minus the generator and valve wheel, for the model 425 series stoves.
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.
Reproduction valve stem for the model 200A lantern. Comes with a new valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
Looks like it may have gotten a little too hot and burned (see photos)
This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.
Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel.
We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
A graphite valve stem packing is included with each of these in case you end up needing to change them.
This is a used knob. I believe this is one of the porcelain knobs for the old AGM kitchen or cabin stoves. Just a hollow star shaped knob. There are no threads on the inside and I am not sure how they were held on. Made of porcelain. Has a diameter of about 1 7/8 inches.
NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Reproduction control knob disc for red Sears lanterns models.
Valve for the 5154B, 5152D, and 5153A propane lanterns with electronic ignition. Comes with ignitor cam and knob/screw.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
This is a new Coleman made valve assembly. Includes the valve, knob w/screw, fuel pick up tube and eccentric block. Fits both the 288 and 288A lanterns.
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..
This is a reproduction knob for the Coleman made M1950 stove. The color of these match the original Coleman made color. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.
This is a reproduction knob for the Rogers made M1950 stove. The color of these match the original Rogers darker color. We have found the earlier stoves (made around 1953) were darker than the newer ones (made around 1963). The last photo shows the difference in color between the two. These will fit any model or make of the M1950. These are made in the USA and have been tested to work well even with the heat these stoves produce. Part of the testing was to check its function on two different M-1950 stoves for an hour at a time by doing multiple on-off-on cycles many times. If you need a screw for this knob, those are HERE, they are a special thread pitch of 4-36 and the common Coleman screws are different.
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
N.O.S Valve stem for the model 335 and 339 lanterns.
Has a small chip on the valve wheel.
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced.