This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many. Comes with a new gasket that you will have to install.
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
New old stock lamp finial.
New old stock finial for lamp.
Used top half of the burner assembly for a slant lantern or lamp.
NOS burner frame, Valve and Generator for the 158, 159 and 159X kerosene lamps. May fit others too. Very nice condition.
Burner assembly for the 158, 159 and 159X kerosene lamps. May fit others too. Valve operates well.
Can't tell if this is NOS or Used - Great Condition.
Shade holder rod for the Model A Lamp and other early models.
Unknown NOS valve stem with fiber wheel. Stem measures 1 1/4 inches.
Does not come with packing or valve stem nut.
Unknown NOS valve stem with fiber wheel. Stem measures 1 1/4 inches.
Handle ring used on the Model A Air-O-Lite and other early Lamps
Shade holder screw for the model 117, 118, and 119 lamp. Looks like the more common shade holder screw but has much larger threads. Will not fit other models.
Early mixing chamber used on the early 220/228B lanterns and lamps of the same period.
Used maroon valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves. Completely interchangeable with valve wheel 425-1491.
This is a used lamp handle for the early lamps like the Model M and other Pre CQ Lamps. Some might show signs of wear. It is 4 3/4 inches long.
NOS burner frame and pick up tube for Lamp Models 139, 152, 152A Gasoline and Kerosene. May fit others too. Will have signs of tarnish due to age.
Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.
These are early style shade holders for the Air-o-Lite Lamps
Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.
Used generator spring for 200, 220, 228, 242, and 275 lanterns. Also fits some Sears models. This is the newer style.
Will show signs of use but will be in good shape.
Steel air intake tube for the old Quicklite lanterns and CQ lamps.
Used burner assembly for the old model 327,427, also for CQ and Air O Lite lanterns. Will also work on other lamps that would have originally taken the Q99 generator.
Used brass filler cap. Will all vary in wear and amount of brass faded. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Will come with a new gasket for you to install if needed.
Original used Finial for Lamps
Used valve body for the slant lanterns and lamps.
This is a used filler cap for the 242 lanterns. Fits the model 242, 242A, 242B, 242C, 242K, 243, 243A, 247, 249 lanterns and the model 500 stove.
Comes with a new gasket for you to installed if needed.
Used fluted lamp fount top. Looks like this fount top was painted purple before.
Used fluted lamp fount top. Looks like this fount top was painted white at one point..
this is an original used Finial for Lamps. This finial is missing the nut that threads onto the bottom.
These are original old stock Coleman made in the USA amber globes. They have the blue line on the top and bottom edge as was common on these. Probably from the late 70's or early 80's. Very limited supply. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249.
This is a used globe for an AGM lantern. Marked heat resisting. The writing is faint as was common on these. These will also fit on 200a lanterns.
These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.
Has a burn mark and one small spot missing the amber (see photos)
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Used shade holder for the old 117, 118 and 119 lamps. All vary in wear and condition.
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
This is a used older style brass mixing chamber for the 220-228 series lanterns.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
Handle nut for Coleman gasoline and kerosene 2 mantle lamps model 139, 152, 152A.
This is a used one piece filler cap. Paint is chipped or missing. Comes with a new gasket that you will have to install.
Used steel filler cap for Coleman lanterns. All will vary in wear.
Comes with a new gasket that you will have to install.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
This is a used one-piece filler cap that is the darker green used on 288 and similar lanterns. Paint may be chipped or scratched; each one will vary in wear. Comes with one new gasket for you to install if needed.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
