Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Used frame plate for the model 220/228 H and J lanterns. Has been cleaned but may show signs of light wear.
Original used grate screw for model 502 stove. Each stove uses a total of three.
These are from used generators - they are straight with no gas tip or pricker rod inside. They will most likely need to be cleaned to be used. The interior may be clear, or it may have remnants of old internal packing/springs.
Stainless Steel grate screw for model 502 stove. Uses a total of three.
Direction disk for the military lanterns. These came out of the old SMP factory.
Fuel tip used on the end of the fuel tubes of early 220/228B lanterns, 236 and some lamps.
Drain cap for the KampKold cooler.
Used direction disk for some propane stoves. Small disk with little less than a 3/4 inch diameter.
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This is a used stove handle for many stoves.
It measures 5 13/16 inches across. Will show signs of rust and wear.
It is know for sure to fit the 413E and a 425C.
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
New cotter pin for the 220B, 235 and other early style bails. This tiny cotter pin may be a little long and will have to be trimmed, but the width is correct to pass through the bail holes.
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Used Base bracket for the Military lanterns.
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Used figure 8 piece as used on the old Q style burner.
This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.
NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit. No other sizes of chain are currently available that are an exact match to what was used.
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
Nut for 220H through K frame bottom.
Needle assembly for Thermos stoves. Measures 11 inches. New old stock but is very rusty.
I believe these are burner tubes for an AGM double mantle lantern. They are 2 7/8 inches long. Roughly the same diameter as Coleman burner tubes. Made of steel.
Top cap for the Leacock lamp handle.
New old stock filler plug for catalytic heater.
Fuel needle. Measures 3 7/8 inches long.
Fuel tube and screen for Thermos stoves. It is 3 inches long.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
This is the gasket only from the 5423A5611 small parts kit. OD 1/2", ID 3/16", Thickness is just under 1/16" Was commonly used on the model 5413, 5413A, 5423, 5430B, 5433, 5430B, 5430C, 5435C, 5435D and similar propane stoves.
Latch cover for the old steel belted coolers.
Unknown Coleman direction disk. I do not know what it goes to. It is a small disk with only an 11/16 inch diameter.
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Collar assembly for the model 5107 and 5107A lantern. New old stock but has some scratches.
