Air Tube Screw - S72
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Used direction disk for some propane stoves. Small disk with little less than a 3/4 inch diameter.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is a screw for 242 pumps where the top of the pump fits inside the fount and for other applications with this thread.
NOS Direction disk. Small disk with little less than a 3/4 inch diameter. Mostly used on propane stoves - will be way too small for a GPA lantern or stove.
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is the small check ball for the 427 lantern with an external pump. In the photo below, you can see the application. These are made from 440C Stainless Steel, the original was brass.
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Used filler plug for catalytic heaters, green color. Gaskets seem in really good shape
Used Vent bracket.
Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern.
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is 12" of 100% natural cotton wick for Kerosene oil lamps. Used in some models of Handlan lamps that use the round 1/4" wick similar to this one:
This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.
This fits many applications for propane appliances.
This is the brass screw used in M-1950 stove valve knob. Can also for 242 pumps where the top of the pump fits inside the fount..
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
Vent bracket.
Used on the 5154-700 and 5154B700 Electronic Ignition Propane Lantern.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.