Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
Fits the model 5114 and 5114A propane lanterns
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Frame bolt. Fits the 5107C, 5114C, 5151, 5152. May fit others.
Used direction disk for some propane stoves. Small disk with little less than a 3/4 inch diameter.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
NOS Direction disk. Small disk with little less than a 3/4 inch diameter. Mostly used on propane stoves - will be way too small for a GPA lantern or stove.
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
Collar assembly for the model 5107 and 5107A lantern. New old stock but has some scratches.
Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.
Used ball nut for the model 275 lantern. This is the checkered variety.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
These Peerless mantles are the same size as Coleman #11 or #1111 mantles. Made in India. For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles, suitable for 500 candlepower lanterns.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Coleman #51 Mantles. 2 per pack Fits models 3018, 3023, 3112, 5130, 5132, 5133, 5134, 5136, and 9742
Also known as part number 2000026608.
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
Filler cap lanyard for the small backpacking lanterns.
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
String Tie Mantles for Models 222, 226, 229, and 3022 lanterns
Also known as part number 3000004346.
#11 mantles 2 pack For lantern model numbers: 206, 236, 237, 333, 555, 621, 625, 635, and 639. These are the larger mantles.
Coleman's Most Popular Sized Mantles. 2 mantles per pack.
Use on these lanterns: 200, 201, 214, 220, 228, 242, 243, 249, 275, 282, 285, 286, 288, 290, 295, 5107, 5114, 5150, 5155, 5152, 5153, 5154, 5155, 5156, 5157, 5159, 5177, 5178, 9950, 9960
Also known as part number 3000004345.
This is a used newer style U tube - does not come with venturi
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
Vent nut for the Northstar lantern.
Vent rod for the model 5114 propane lantern.
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
Reproduction generator nut for all the model 200, 242, 243, 220, and 228 models.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
