Washer Plate Used - E1107
Used frame plate for the model 220/228 H and J lanterns. Has been cleaned but may show signs of light wear.
Used frame plate for the model 220/228 H and J lanterns. Has been cleaned but may show signs of light wear.
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
1/2 inch long screw for the 500 stove. Requires two for the Cap and Fillers. See description tab for more details.
Unknown screen. Measures 1/2 inch in diameter. Very fine brass. Seems too fine to be for a burner screen. Came out of a lot of old AGM parts.
Burner support screw for a 502 stove. Each stove requires 3 total.
Screw/Bolt for the burners on 5435A and 5435B Stoves. 2 are needed for both stoves.
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.
This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.
New 200 burner frame Pal Nut is HERE.
New 200 burner frame Nut is HERE.
I believe these are burner tubes for an AGM double mantle lantern. They are 2 7/8 inches long. Roughly the same diameter as Coleman burner tubes. Made of steel.
New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Brass reproduction burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉.
Sheets are 4-3/4" in diameter and 1/32" thick.
Steel burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long. These are the older style gray looking steel tubes as used on lanterns and lamps made during the war years.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
Term-Sport Alcohol Stove Gasket Set. These gaskets are for the filler cap and the burner tube. Both are made from fuel resistant materials that will last for years (ECH - Cap & Viton - Burner Tube).
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.
Term-Sport Alcohol Stove Burner Cover Label. This decal is the waterslide type - not peel and stick. Click on the "Description" under the photo to see the installation instructions.
Used burner support for the 502 stove. Will have varying rust on each one but all are solid.
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
Spring Clip for 249 Preheater Cup. This is an exact reproduction. Fits well also on the 200, 202 frames also - see photos. Part also known as 235-3111
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
Used frame bottom plate for the model 290A and all 295 models. This is a used part and conditions vary one to another.
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.
These will not fit the 530 stove without using a 1950 generator and a 530 needle.