- Free Shipping
Valve Stem Washer - S44
This is the gasket that goes on the 5400-5211 valve stem. It is a small flat washer. Known to fit models 5410A700, but may fit others.
This does not work on the 5430A700 or the 5430B700.
This is the gasket that goes on the 5400-5211 valve stem. It is a small flat washer. Known to fit models 5410A700, but may fit others.
This does not work on the 5430A700 or the 5430B700.
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7.
It has been reported that the 285 valve stem uses 2 of these.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7
It has been reported that the 285 valve stem uses 2 of these.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Used valve stem packing nut. Will also require a P01 graphite packing located HERE.
Reproduction valve stem bushing for the 327 and 427 Quicklite lanterns.
This is the small, beveled bushing that goes on the valve stem below the graphite packing on the 200, 200A, 202, 242, and 243 lanterns, along with many stoves that have a 1/4" valve shaft.
Reproduction long air stem with newer style screw end. Same length as the 216-532 air stem. Allows the use of the new style check valve with the smaller threaded end for stoves that took a longer air stem. Overall length is 5.5".
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
Unknown valve stem. Has a tag on it that says it is part number 4-4005. Measures about 3 1/2 inches long.
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.
Valve stem that I can't identify. Has a pointed end. It is 1 3/4 inches long. Has a smaller diameter shaft that would take the small packing. The valve stem nut is for a 7/16 wrench. Has a solid formed wheel that is not held on with a screw.
Used valve Stem for the 413E, 413F, 413G, 413H, 425F, 425G, 426D, 442, 442A stoves. Also fits Sears stove models 476.72302, 476.72303, 47.74970 & 476.74980.
You will need a P01 graphite packing for these which is HERE. Measurements: just over 1-3/4" long and 1/4" diameter.
Please read this if you have a 425F: This has the 1/4" diameter width, not the smaller 3/16". The 425F came with both the 3/16" and the 1/4". The model 425F was a transition year, so be sure to measure your current valve stem and make sure it is 1/4".
Used long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
This is a valve stem for a Canadian iron, but we do not know the part number or which models it fits. The length of the entire shaft from the base of the handle to the tip is 1/5". The valve stem has been drilled out and can accept a rod.
Unknown NOS valve stem with fiber wheel. Stem measures 1 1/4 inches.
Does not come with packing or valve stem nut.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
Used valve stem for the model 220/228H, J, and K lanterns. Has been cleaned and will have new graphite packing.
Unknown NOS valve stem with fiber wheel. Stem measures 1 1/4 inches.
Reproduction valve stem for the model 200A lantern. Comes with a new valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
These are new old stock and have a bit of rust on them from sitting on a shelf for decades. Comes with a packing from the factory. Fits stoves 3F, 3H, 413B, 413C, 413D, 418, 418B, 419, 420, 371, 371A. Does not come with the needle. If your stove has been updated to a later valve style then this would not fit.
The needle and holder for this is part number 471-2381 HERE.
A whole new valve and gen would be part number 413B6601. That is the valve that fits the 413E and 413G stoves.
NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.
Found on the earlier than 425F stove models. Use part 412-2531 to make a complete valve assembly.
Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.
P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
This is reproduction of the older style of check valve that would take the original air stem with the larger end. Excellent craftsmanship on these.
Also known as 242B5381
Used valve stem for the model 200A lantern. Has been cleaned, and packing changed.
Valve stem only. Fits the 413E, 413F, 413G, 413H, 425F, 426E, 442, 442A, Sears Models 476.72303, 476.74980, 476.72302, and 476.74970. Comes with a new packing installed. Also known as part number 413A2521.
Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.
NOS valve stem for many of the older Coleman stoves. Compare your diagram with the part number 412-253 to verify it will fit. Will not fit into the 414, 424, 425, 426 series stoves.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.