252 Filler Cap Chain Bracket - R506
This is the small part that attaches to the filler cap screw so you can hook the chain to it.
This is the small part that attaches to the filler cap screw so you can hook the chain to it.
1/2 inch long screw for the 500 stove. Requires two for the Cap and Fillers. See description tab for more details.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
New filler cap screw for the small 242 & 249 lanterns and 500 stove size filler caps.
Empty parts tube for the M1941, M1942, 520 and 523 military stoves. Tube is 4" end to end with caps on.
This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This small gasket is for the model 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap.
Also fits the model 500 stove and the early 520 stoves. The green filler cap is shown for identification purposes only and is not included.
Filler plug gasket for the model CQ lamps,327 Quicklite lanterns and many older stoves. Can be used in place of the 104-136 lead gasket. Also fits the 523 military stove.
This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This gasket is for the model 227, 427, 220/228 Slant lanterns, most winged style fuel caps, early 220B's, and other similar lanterns and lamps that have the older style cap insert.
It is the same outside diameter as the common three piece cap gasket but has a smaller inside hole.
Old part number 115-1361.
This will not seal they typical Coleman lantern cap.
This is a used brass outer cap for the table lamps that did not have an internal pump. Fits lamps 129, 129A, 129G, 130G, 130K, 130P. 131P, 133, 134A, 134P, 134G, 143, 150B, 150G, 150R, 150I, 150BK, 150GK, 150RK, and 150IK. Fits stoves 375, 375A, 376, 377, 378, 378A, 379, and 379A. Fits Handy Gas Plants 458 and 458G.
Chain for military lanterns and stoves. Read note below please. These are 8" long and has 15 total links, which is long enough to use on one funnel and one cap on a military lantern and have an inch left over.
NOTE: These links are slightly too big to fit in the original slots on funnels or cap clips. The first & last links will have to be modified slightly to fit. The circular part of the chain link can be bent smaller then flattened out to original the original size to fit in the cap clip - grinding them down would probably make it too weak. It will not fit into the military funnel slot - the slot would have to be enlarged in width about 1/16 of an inch to fit. No other sizes of chain are currently available that are an exact match to what was used.
This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
NOS metal pump cap for pump assembly. Does not come with whole assembly - just the top exterior metal cap is included.
This is a new plastic filler funnel. Small and easy to pack. Works well for standard sized filler caps. Also, the funnel tip just fits inside the smaller style caps like on the 242, 243 and some 500 stoves.
Cap gasket for Akron lanterns. Outside diameter is 5/8 of an inch. Inside diameter is 3/8 of an inch. Thickness is 1/8 inch.
These come from a Thermos fount with a standard type of pump similar to Coleman. These hold the pump cap into the fount. Will not work on Thermos lanterns where the pump screws onto the fount. Comes as a set of two.
Term-Sport Alcohol Stove Gasket Set. These gaskets are for the filler cap and the burner tube. Both are made from fuel resistant materials that will last for years (ECH - Cap & Viton - Burner Tube).
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
O rings for the Thermos lantern and stove pumps. One is for the pump, the other is for the top seal. These are for the later model Thermos lanterns and stoves where the pump and filler cap where combined.
Jug cap that fits most Coleman jugs. Does not have a gasket - this is the cap only. Will need a gasket to seal well.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
New burner cap for the model 242 series lanterns. Also fits the 200, 200A, 202, 243, and 247 lanterns.
Solid brass with stainless steel screen.
This is a complete rebuild kit for the pump on an M1942 stove. You will get the cap gasket, check valve dot, and pump leather.
New burner cap & screen for the model 236, 237 and 249 lanterns.
Solid brass with stainless steel screen.
This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242 and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.
New, reproduction burner cap for 321, 331, 335, 339, 621, 625, 635 and 639 lanterns. Solid brass with stainless steel screen.
Also known as part number 335-315
This is a complete rebuild kit for the pump on an M1950 stove. You will get the cap gasket, check valve dot, fuel tube gasket and pump leather.
This is a used one piece brass filler cap. Wear will vary.
Comes with a new gasket that you will have to install.
Wrench used to remove diamond cap drain assembly on the Snow-Lite Cooler series. May fit in others. Stores in the interior drain hole when not in use. These have been in storage on a shelf for a long time and may show some surface rust.
New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.
Round steel burner cap for most models of double mantle lanterns and lamps.
Used filler cap that will fit most lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
These are all assorted colors that have missing paint, are tarnished or have been repainted and do not match the original color - photo is for illustration purposes only - comes with one filler cap and new gasket you will have to install.
Filler cap insert for the models 242, 242A, 242B, 242C, 243, 243A, 234, 234A, 247, 249 and other similar lanterns and lamps that take the smaller filler cap. Also fits the model 500 stove. Will have a new gasket installed.
This is a cap for the end of the M1950 pump. This screws into the bottom of the pump.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.