Search

Here is a kit of the most commonly used parts when repairing most lanterns and stoves. Buying kits saves in overall cost and comes with free shipping anywhere in the USA.

• 4 new Coleman check valves
• 10 Leather pump cups - pre-oiled
• 5 Neoprene rubber pump cups
• 10 Large valve stem packings for 1/4" 
• 5 Small valve stem packings for 3/16" 
• 10 Generator tube packings
• 10 One-piece fuel cap gaskets
• 10 Three-piece fuel cap gaskets
• 10 Cap gaskets sized for the 242 or 500 stoves
• 20 Peerless Mantles with Thorium 21A size for most double and single mantle lanterns

These are original Coleman made in the USA amber globes. Some will have the blue line on the top and bottom edge as was common on these. Most likely made during 1960. Used on lanterns from 1960 to 1980. This globe will fit models 200, 200A, 200B, 242A, 242B, 242C, 243, 243A, 234, 201, 202, and 249. "Made in U.S.A." on globe.

Has a few imperfections in the glass, color is faded and has one burn mark (see photos)

This is an original 220 Coleman vent. The black porcelain finish was custom done by Independence Porcelain Enamel (IPE). This is for the late 220F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.

This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below. 

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.

This product is not included in the OCP free shipping program.

Photo's with lanterns are for illustration purposes only.

Eccentric lever assembly for the inverted lantern.

Valve stem for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

Original used green sunrise logo lamp globe. Although used it will have no defects. Logo is very lightly stamped as was common back in the old days. This globe measures 6 inches tall. The top rim opening has a 3 5/8 inch diameter. The bottom opening has a 3 1/2 inch diameter. It bulges out at the widest point to about 5 inches.

NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.

Fits models Air O lantern, 327, 427, Slant 220 lanterns and CQ lamps

NOS gas tip for Model A Lamps and possibly other early Torch-Lite Lamps.

Reproduction Q99 generator for the old Quicklite style lanterns and lamps. They work great.

Lamp valve for 130G, 130K 130P and 131P.  The bottom is threaded for a fuel and air tube to be attached.

Reproduction filler plug for the old Quicklite lanterns and lamps. Made of solid brass. Now you can replace your old rounded off filler plug. Made to use the 427 gasket rather than the old lead gasket. Will come with the new gasket.

This is a new production T-handle pump. It works great to pressurize your lantern, lamp, or Handy Gas Plant. Approximately 10 inches long.

Reproduction lamp globe for the later style Coleman lamps. Real nice alternative to an expensive original. This globe measures 5 7/8 inches tall. The top rim opening has a 3 inch diameter. The bottom opening has a 3 5/16 inch diameter. It bulges out at the widest point to about 5 inches. Some people call this the 355 globe.

New cooler tray. This tray measures approximately 9" X 11-9/16" and is 2-3/4 inches deep. Has some yellowing from age but is in good shape with no cracks or holes.

These fit in cooler models: 5252, 5253,  5252B, 5252C, 5253A, 5279, 5280, 5280A, 5285, 5285A, 5285B, 5283A, 5284, 5284A, 5284B, 5281, 5282

This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.

Has a 7/8 inch diameter and is made in the USA of oiled leather.

This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.

This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.

Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201. 

Made of 100% graphite.

New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.

Generator for some model of AGM lantern. Measures only 1 9/16 inches long.

Used shade holder for the old 117, 118 and 119 lamps. All vary in wear and condition.

Bulk adaptor

These mica panels are 3" x 5" in size.

General information:

• Mica can be cut with sharp scissors or a good paper cutter
• This is the only size that is available
• Mica is a natural product that is mined from the earth and will have slight variations in clarity, thickness, lines and light scratches.
• Mica is not available in amber or red.
• Mica can withstand temperatures up to 1800 degrees F.
• These are only sold in a package of 5 panels.

For those in need of a rugged, unbreakable globe, these reproduction Mica Globes fit the bill. Their built-in reflector optimizes light distribution. If needed, you can drill a hole into the reflector for easy lighting.

These made in the USA Mica Globes measure 4 1/2" x 3 1/2" and fit the 200, 200A, 234, 243, 241, 242, 246, 247, and 249 lanterns.

Valve for the small military 527 stove.

New old stock finial for lamp.

Amish style filler plug for the early Quick-Lite lanterns and lamps. Does not use an air stem and requires a hand pump.

This is a used pump assembly for the model 220b. It would also be correct for the 427, 228B, 235, 220BX, 220C, and 228C lanterns. It would also fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B.  It has been cleaned and has a new pump leather installed. It may show signs of wear and could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style one labeled "Thin" with the thinner knurled portion which is 1/4" thick. Has a nickel plated brass cap.

Used top half of the burner assembly for a slant lantern or lamp.

This is a used lamp handle for the early lamps like the Model M and other Pre CQ Lamps. Some might show signs of wear. It is 4 3/4 inches long.

Unknown Coleman valve and generator. I can't figure out what this fits or a part number for it. Measures 11 1/2 inches long.

Pre-heater generator for the Urn Burner 404, 505, 707; Water heater 1; Handy Gas Plant 5052; Pre-heater 544-383.

Valve Assembly for the model 502 stove without fuel pickup tube. 

Reproduction generator for 220, 228, 275, and similar Sears lanterns. New generator includes new gas tip, spring, and tip cleaning wire.

Reproduction check valve. This is the earlier larger style check valve as used on the L227, L427, 220B, 228B, 220C, 228C, 235 lanterns, some lamps, and some early stoves.

Used Bulk Adapter

Interchangeable with the Q99 or R55 generator. Fits the model 327, 427 and Slant 220 lanterns. NOS - This does not come in original packaging and they are rusty on the outside. They are made of steel.

Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.

NOS long air stem that fits the larger check valve used on the 220/228B and 220/228C lanterns. Also fits military lanterns. Measures 5 9/16 inches long.

This is a used pump assembly for the model 220C. It has a thick steel knurled pump cap rather than brass. The steel cap was usually found on the models 220/228C made during the war years. It would also fit the 427, 228B, 235, 220BX, 220B, and 228C lanterns. It would fit the lamp models 118, 118A, 118B, 119, 119A, 132A, 132P, 138A, and 138B. This is a used pump assembly. It has a new pump leather installed. It may show signs of wear and surface rust. Could have some light wrench marks on the knurled portion of the cap. It won't be all rounded off or in bad shape. You are purchasing the style labeled "Thick" with the thicker knurled portion which is 5/16" thick.

Made by Coleman. 2 hinges, 8 screws included. Packaged in Coleman branded bag. Coleman cooler Stainless Steel hinge set. Hinge size: 2" H x 2.25" W.  Center of screw holes: Width = 1.5", Height - adjustable between 1-1/4" to 1-1/2".

Most coolers have the model number on the bottom. Review our parts diagrams for your model visually if you cannot locate the model number. Parts diagram page is HERE.

For use on the following Coleman Cooler Models: 5226 5227b 5240 5241 5241a 5245 5250 5255 5256 5277 5297 5298 5299 5299a 5848 5850 5862 5884 5887 5896 6050 6154, 6155, 6200 6201 6240 6250 6251 6257 6260 6262 6263 6270 6273 6281 6286 6296 6297, 6298, 6498, 6499; UPC: 07650139946. Coleman part number 3000005298. Can be interchanged with previous part numbers 6262-1141, 5256-1851, and 5283-1141.

Also known as part number 3000005301.

Used Valve Stem Assembly for the model 502 stove. Does not come with the valve wheel.

Comes with a new packing installed.

This is a reproduction lamp globe holder that allows you to use a common 220 size globe on your lamp. The original lamp globes are expensive and this is a great alternative. Burn your old lamps and no longer worry about breaking a rare globe. Globe is not included.

Used valve body for the slant lanterns and lamps.

Used filler cap with lanyard for the small backpacking lanterns - in very nice shape. Will also fit most other lantern and stoves that use the standard size filler cap.  Comes with a new gasket that you will have to install.