Lamp Burner Assy with Valve & Generator, NOS - E1002
NOS burner frame, Valve and Generator for the 158, 159 and 159X kerosene lamps. May fit others too. Very nice condition.
NOS burner frame, Valve and Generator for the 158, 159 and 159X kerosene lamps. May fit others too. Very nice condition.
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one is in very good condition.
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)
Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.
This is a service pack for burner 1222 - R1A and R55 heaters
NOS Burner Cap for the early stove models 2, 9, 2C, 9C, 2E, 9E, 2F, and 9F
Cannot be used on the Model 1.
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
New burner assembly for the model 286 lantern. The burner tube is brass.Â
Burner assembly for the model 288 lanterns. The burner tubes are brass.
This is a reproduction burner ball for the Focus 5 heater. Has been field tested and works excellent. Comes with instructions on how to remove the screen from your old ball and install the new - see those instructions in the "Description" area below. Made of stainless steel. The smaller inner screen would need to be good on your current burner for it to work correctly. Made in the USA.
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.
This is a used burner assembly with the round mixing chamber that will fit the model 220F & 228F. It will be in fine working condition. It may show signs of tarnish and other spots from being old.
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
This one will need a new burner cap or screen.
Is marked with 3000.
This is a used Burner frame for the 242A through C lantern. Will also work on the 247.
Is stamped with 3000.
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Burner frame for the 158, 159 and 159X kerosene lamps. May fit others too. Valve turns and seems to operate smoothly.
Burner assembly for the rare 414 gas stove with electronic ignition.
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
Is stamped with 3000.
This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Pre-heater generator for the Urn Burner 404, 505, 707; Water heater 1; Handy Gas Plant 5052; Pre-heater 544-383.
This is a used vent. Has some paint chipping (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping and one small dent on the outer rim (see photos).
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Used burner assembly for the Thermos 2 mantle lantern. In good shape.
Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.
Used burner assembly for the old model 327,427, also for CQ and Air O Lite lanterns. Will also work on other lamps that would have originally taken the Q99 generator.
Parts tube for the M1941, M1942, 520 and 523 military stoves. Each contains a new vaporizer, gas tip, large packing, and 3 screens. LINK for great info on these and what they fit.
Burner Assembly for the model 288 lanterns. The burner tubes are steel. Will vary in wear.
New old stock stove tank for the 3 burner Thermos stove models 8431 and 8432.
Used burner fillers and cap for the model 502 stove. Has some rust but seems to be in good shape.
This one has paint chipping and top outside rim has a dent (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
Brass Vent Bolt for 243B, and all 241 Lanterns - this bolts down into the top of the frame to hold the vent.
Brass Vent Bolt for 243, and 243A Lantern - this screws down into the top of the frame for the 243 vent to sit on.