This is an original 220 Coleman vent. The black porcelain finish was custom done by Independence Porcelain Enamel (IPE). This is for the late 220F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
This is a used fount for the 200A lantern dated 6-76. This fount as a couple paint chipping/scuffs, overall great condition (see photos)
This is a used vent for models 227 and 228B through 228E. Very nice. Has a couple small paint chips (see photos).
This is a used fount for the model 200A lantern. Has some paint chipping, scratches/scuffs and two very small dents you can only see in certain lights (see photos). Otherwise in nice shape - inside of tank looks good too.
This is an early style 228 ventilator. This vent has a couple paint chips and small white dots that might come out but is otherwise in great condition (see photos)
Used tall style vent for the 200/200A lanterns.
This one has some scratches and paint chipping (see photos)
Used tall style vent for 200/200A lanterns made in 1962 and before. This vent has some rust and chippings (see photos).Â
This is a used fount for the 220/228K lantern dated 5-73. It has a couple paint chips and some writing on the bottom of the tank, otherwise it is in good shape.
It will work for any 220/228H through 220K type models.
This is a used tall style vent for the 200 and 200A Lantern.
Has some paint chips (see photos)
This is a used old style fount for the 220/228B through 220/228F lanterns.
Has small scratches/scuffs, chips and looks like some plastic got melted to the outside but might be able to get it off (see photos).
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
Used short style vent for 200/200A lanterns. This vent has some paint chipping (see photos)
Used short style vent for the 200/200A lanterns. Has a some scratches/scuffs and paint chips (see photos).
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-65.
Has paint chipping and a couple scratches/scuffs (see photos)
This is a used ventilator for the model 220B through 220E lantern.
Has some paint chips and scratches (see photos)
Used short style vent for the 200/200A lanterns made in 1963 and after.
This vent has some scratches/scuffs and paint chippings (shown in photos)Â
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62.
Has paint chipping and some rust (see photos)
Fount dated 12-80. For models 220/228 H thru K. Has some scuffs/scratches and paint chipping on the bottom of the fount (see photos).
This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.
This is a used burner assembly with the round mixing chamber that will fit the model 220F & 228F. It will be in fine working condition. It may show signs of tarnish and other spots from being old.
This is a used vent. It will fit models 220B through 220E.
Has paint chippings and a small bulge towards by the ball nut opening (see photos)
This is a used ventilator for the model 220B through 220E lantern.
This vent has a few paint chippings. (see photos)
This is a used fount for the 200A lantern dated 9-60. Has some scratches/paint chipping and a dent by the pump assembly (see photos)
This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Fount dated 5-77 for the model 220/228 Lanterns, models H thru K. This fount has some scratches, paint chipping, and rust - see photos.
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
This is a used ventilator for the model 220B through 220E lantern. This vent has paint chips (see photos)
This is a used vent. Has some paint chipping (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping and one small dent on the outer rim (see photos).
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Used valve assembly. Fits models 220H-J & 228H-J and 220K lantern. Valve packing has not been changed on these. If needed, those are HERE.
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
Used burner frame for the models 228H and 228J lanterns.
This one has paint chipping and top outside rim has a dent (see photos).
This is a used ventilator for the late 228F made after 1971 and also the G, H, K and J models. These fit on a wider burner frame, but will also fit on the early F with a smaller frame but will be a bit loose.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
Used burner frame for the models 220H and 220J lanterns.
Used burner frame for the models 220H and 220J lanterns.
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
Used burner frame that will fit models 220B through early 220F through approximately 1971.
This is a used burner frame for the model 200A lantern.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Used burner frame for the models 228H and 228J lanterns.
This is a used burner frame that will fit models 228B through 228F.
Has a bit of rust
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This is a used collar for the model 200A lantern.
It may show signs of wear/scratches. Each collar may slightly vary in wear.
