Hollow Wire, NOS - E1347
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 5ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 5ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 4ft and diameter is 3/16"
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one is in very good condition.
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)
Reproduction generator for the Sunshine Safety lanterns and lamps. Similar to the Coleman Q99 but has a different nut. Will not work on Coleman lanterns and lamps.
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 3/16"
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
Unknown Coleman Heater Valves. Measures about 7 3/4" long from the tip to the nut.
Don't know the part number for this valve and generator. It measures 10 1/4 inches long from tip to end of nut.
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 3ft and diameter is 1/8"
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 3/16"
This is a reproduction generator, old style with the square nut. Each includes new gas tip, spring, and tip cleaning wire. This will fit models: 425, 425B, 425C, 425D, 425E, 425F, Sears 476.72301, 476.72244 & 476.74960.
This is a used vent. It will fit models 220B through 220E.
Has paint chippings and a small bulge towards by the ball nut opening (see photos)
NOS maintenance kit for the 639 and 635B Lantern. Comes with a new generator, neoprene pump cup and push on nut.
From Terry Marsh's site: This wrench came with a Coleman L220 lantern dated Aug. 1928. The instructions with the lantern identify this wrench as part no. 362-950. It is 4″ long and fits nut sizes 11/16, 7/16, & 2, 5/16″ plus a 5/32″ slotted generator tip remover. This wrench also came with iron Models 4A & 609.  Link is HERE.
This is a new Hollow wire with jamb nut for Coleman hollow wire systems. Length is 2ft and diameter is 1/8"
Used generator for the model 413E and 443 stoves according to early part diagrams.
I believe it is the same generator as part number 413A5621.
This is the earlier style with the square soldered on nut which does make it easier to install. Comes with tip needle, coil and housing. This one is in good shape.
this is an original used Finial for Lamps. This finial is missing the nut that threads onto the bottom.
This is a new Coleman made generator for Model 290, 290A and 295 Lantern. Each includes new gas tip, spring, and cleaning needle.
This generator can be used on the 290 series lanterns, but you will have to use your original generator nut instead of the new one that comes with this generator. The 290 generators have been discontinued.
These are also known as part number 3000005404 and replaces the 290 & 290A part number of 290-5891.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Valve minus the generator. Use part 413A6531 to make a complete valve assembly along with a graphite packing and valve stem nut. This valve body requires a valve stem that is 1/4" in size, not the smaller 3/16". Please check yours if there is any doubt about the tank/generator not being original on your stove.
P01 Graphite packing is HERE, and the valve stem nut is HERE, and the valve stem is HERE (if the parts are in stock currently).
This is a used ball nut for the 247, 249, and 242 Lanterns - except it will not fit the 242 No Letter / Junior.
Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.
They will all show varying signs of wear.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Parts kit for the model 5151A propane lantern. Includes heat shield, vent bracket, 2 gaskets and nut.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.
Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
This is a reproduction generator nut for the first Coleman lantern, the Arc lantern.
Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
Valve stem that I can't identify. Has a pointed end. It is 1 3/4 inches long. Has a smaller diameter shaft that would take the small packing. The valve stem nut is for a 7/16 wrench. Has a solid formed wheel that is not held on with a screw.
Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.
Ball nut for the Canadian made 242, 247 and similar lanterns. This was also the ball nut that Coleman sold as a replacement ball nut in the US.
They will all show varying signs of wear/ wrench marks.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Original NOS generator nut for the Milspec lantern. Military part number 6260-00-161-1859
Reproduction generator nut for the 252 military lantern. Made of brass.
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.