- New!
Lamp Handle Ring, Used - E1157
Handle ring used on the Model A Air-O-Lite and other early Lamps
Handle ring used on the Model A Air-O-Lite and other early Lamps
Short pump assembly for Thermos lanterns. Pump barrel measures 3 inches. Will most likely need a new O-ring kit which are HERE.
This kit is for the 550 stove specifically. It includes 4 O-rings.
Set of 3 O-rings for some Coleman lanterns and backpack stoves. These are the 3 most common sizes of O-rings needed. Most lanterns and small stoves take two. You will get one of each size so there is a good chance you will be able to rebuild whatever you have.
O-Ring sizes are #6, #7, and #9, made of Flourosilicone.
We know it does work on these models: 533, 440, 442
Does not work on the 400B, 508B, 533A, 3024
This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.
New feed tube assembly made by Coleman. Includes new Schrader valve and O-ring. Fits all 282, 285, 286, and 288 model lanterns.
O rings for the Thermos lantern and stove pumps. One is for the pump, the other is for the top seal. These are for the later model Thermos lanterns and stoves where the pump and filler cap where combined.
New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉.
Sheets are 4-3/4" in diameter and 1/32" thick.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone.
It is verified it will fit the 533 Stove - 2 are needed.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8
This has been reported to be the correct size to repair the valve on the 400B and the 533A stoves. One is needed for both.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7
It has been reported that the 285 valve stem uses 2 of these.
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #9.
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8.
This one black Viton O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #7.
It has been reported that the 285 valve stem uses 2 of these.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #6
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #5
Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
O ring made of gas resistant Viton. Outer diameter 7/16". Works on many propane stove models such as 5400A.
Two required for the model 550 stove.
This is the ring that attaches to the collar of the lantern so you can hook a chain to it. Rings are stainless.