Search

New old stock valve assembly for the QuickLite model 327 lantern.

Used gold clamshell carry case dated 11-80 for models 275, 290, 290A, 290B, 295, 220/228 F, G, H, J, K and other similar sized lanterns. Will not fit Lanterns with the tall style vent like 220/228 B thru E, Quick-Lite or Mil-Spec Lanterns.

This product is not included in the OCP free shipping program.

Photo's with lanterns are for illustration purposes only.

Fits models Air O lantern, 327, 427, Slant 220 lanterns and CQ lamps

Used fount for the model 327 Quick-lite lantern. Dated 9-29.

This one has some dents and scratches but otherwise in nice condition (see photos, the dents are hard to see)

Reproduction Q99 generator for the old Quicklite style lanterns and lamps. They work great.

Reproduction filler plug for the old Quicklite lanterns and lamps. Made of solid brass. Now you can replace your old rounded off filler plug. Made to use the 427 gasket rather than the old lead gasket. Will come with the new gasket.

Used valve stem for Quick-Lite lanterns.

These have not been serviced or cleaned and may need a new P02 packing which is HERE.

This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Valve stem for Quick-Lite lanterns.

These have not been serviced or cleaned and may need a new P02 packing which is HERE.

Amish style filler plug for the early Quick-Lite lanterns and lamps. Does not use an air stem and requires a hand pump.

Interchangeable with the Q99 or R55 generator. Fits the model 327, 427 and Slant 220 lanterns. NOS - This does not come in original packaging and they are rusty on the outside. They are made of steel.

Steel air intake tube for the old Quicklite lanterns and CQ lamps.

This is a used collar for the model 327, 427, and similar lanterns. Some will have some surface rust - all will vary with wear.

Universal pump assembly with a leather cup that fits almost all Coleman lanterns and stoves. 

Does not fit the small Peak 1 lanterns or stoves, and also some older style pumps found on QuickLites and similar lanterns/stoves where the pump cap does not have the clip that holds it onto the fount. Replaces part number 242D5201

Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.

Used gas tip for the Q99 generator and some Quick-Lite Lanterns and Lamps. Very tarnished

Vent rod for the Quick-Lite lanterns. It is 1 1/4 inches long.

Reproduction valve stem bushing for the 327 and 427 Quicklite lanterns.

Typically used to stop a fuel leak from the valve stem on older appliances.

This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.

If you need to check your model, please see the PARTS DIAGRAM PAGE. 

Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.

Made of 100% graphite.

Filler plug gasket for the model CQ lamps,327 Quicklite lanterns and many older stoves. Can be used in place of the 104-136 lead gasket. Also fits the 523 military stove.