Collar 220E, Used - X25
This is a used collar for the 220E lantern. It may show signs of light rust or a little discoloration to the metal. All will vary in wear.
This is a used collar for the 220E lantern. It may show signs of light rust or a little discoloration to the metal. All will vary in wear.
This is a used ventilator for the model 220B through 220E lantern. This vent has paint chips (see photos)
This is a new gasket for your metal snap on parts safe. Fits the 220 size metal safe.
Round steel burner cap for most models of double mantle lanterns and lamps.
New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Coleman Lantern Logo for 1955 to 1961 220 & 228 E Lanterns
This is a used ventilator for the model 220B through 220E lantern.
Has some paint chips and scratches (see photos)
This is a used ventilator for the model 220B through 220E lantern.
This vent has a few paint chippings. (see photos)
Coleman Lantern Logo for 1951 200A and 1951 thru 1954 220 & 228E Lanterns
No Border Logo with "Reg." & "Lantern" for 1961 to 1964 200A, 220 & 228 E & F Lanterns
N.O.S Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
This is a used vent. It will fit models 220B through 220E.
Has paint chippings and a small bulge towards by the ball nut opening (see photos)
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
This is a used inner disc for the old 3 piece caps. May or may not have old gasket but one will be provided for you if needed. All will vary in amount of wear.
HERE is a new filler cap screw if needed.
For Coleman Double-Mantle Kerosene Lanterns like the 231 and 235. This may fit and work on a 206 also. Another name for this is the T44. It is the kerosene version of the 220E generator.
Used Sears small hat ventilator. Will also work on the model 220 lantern. This one has some paint chipping and a dent (see photos)
Used burner frame that will fit models 220B through early 220F through approximately 1971.
NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.
This is a used valve assembly for the models 220/228B through 220/228F lanterns. Valve packing has not been changed. If needed, they are HERE.
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-62.
Has paint chipping and some rust (see photos)
This is a used old style fount for the 220/228B through 220/228F lanterns. It is dated 12-65.
Has paint chipping and a couple scratches/scuffs (see photos)
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one is in very good condition.
This is a used burner assembly that will fit models 220/228B through 220/228E. It will show signs of use but will be in good condition. Has the long vent rod for the taller vents. If you change the vent rod to a shorter one, (HERE) it would work fine for a 220F.
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
This is a used old style fount for the 220/228B through 220/228F lanterns.
Has small scratches/scuffs, chips and looks like some plastic got melted to the outside but might be able to get it off (see photos).
This is for a qty of one used pump screw. This is the smaller sheet metal style screw used on the 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Used Lantern light reflector. These are meant to hook into the lower burner frame holes on a 220 and then also the ball nut on top. Should fit all lanterns with similar burner frame holes. See photos. Lantern not included, just for demonstration purposes only.
This one looks like someone replaced the rivets and the edges of the reflector are a little bent (see photos)
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
Used direction disk for the earlier double mantle lanterns such as 220/228B, C, D, E, and F. Will show signs of wear but still be in good condition. May be a transition disk between the 70's & 80's model lanterns.
This is the smaller sheet metal style screw used on the 202, 220/228D, 220/228E, and early 200A lanterns. It is not the one for the 242 series lanterns. Much too small for the 242 series lanterns. Also known as part number 530-452.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
This is a reproduction mica globe for the model 327 lantern. It will also fit on any lanterns that would take a 220 size globe. It is 5 1/4 inches tall. It has a diameter of approximately 4 7/8 inches. The craftsmanship is nice and it is like the old mica globes that went into the first lanterns. Has a lighting door. Mica is a mineral. It may have variations in clarity, small spots, light scratches or other natural discolorations.
Used Needle for the fuel and air tube inside the fount. Used on 220 and 228 series lanterns up thru model F and the 118B lamp.
This is a used older style brass mixing chamber for the 220-228 series lanterns.
This is a old timey steel tube made back in WWII and would have been used on the 220C model lanterns.
Used needle assembly for the 220E5891 generator. Will show signs of discoloration from being used, but will have a good needle. Used in all 220 and 228 model lanterns except for the slant valve models. Also used in lamps 118B, 132A, 133, & 143. Sears models 476.72213, 476.72212, & 476.74070.
This is a newer style mixing chamber for the 220-228 series lanterns. It is plated with a zinc coating or something similar.
This is a used mixing chamber. May or may not have a vent rod and air tube screw.
Mixing chamber for lamps and lanterns. It has the burner tube holes at a wider spacing than the normal mixing chambers. The burner tube holes are 1/1/2 inches apart center to center. Normal mixing chambers are spaced 1 3/8.
New reproduction direction disk for the many of the 2 mantle lanterns made in the USA like the 220 and 228 models B thru F. These are aluminum and look and feel identical to the original, and they are made here in the USA. They come with a protective plastic coating that can be removed before installation.
This disc refers to "mantles" as opposed to "mantle" for a single mantle lantern.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Reproduction burner tube that measures 2 1/2 inches long. Some early lanterns and lamps took this size.
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 3/4 inches long.
This is the set of bushings used on both sides of the graphite packing on the valve stem of the 220/228B through 220/228K lanterns.
Used reflector with pistol grip for the model 220 and 228 B-F lanterns. Really good shape and solid. This hooks onto the post of the burner frame - top and bottom. See photos. Lantern not included.