- Free Shipping
222/226/229 Generator Needle - S127
New Reproduction Generator Needle for Model 222, 222A, 222B, 226 and the 229.
New Reproduction Generator Needle for Model 222, 222A, 222B, 226 and the 229.
This kit includes two blue Flourosilicone O-rings for the valve stem and one Viton black ring for the fuel & air tube attached to the bottom of the valve. They are the proper replacement size for these models: 222A, 222B, and the 226.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #5
NOS gas tip for Model A Lamps and possibly other early Torch-Lite Lamps.
String Tie Mantles for Models 222, 226, 229, and 3022 lanterns
Also known as part number 3000004346.
Pump assembly. Comes with the neoprene pump cup and metal cap. Fits the smaller backpacking 400 series stoves and 222, 226, 229 series lanterns.
Reproduction Generator for Model 226A700 and the 226-700. Generator includes new gas tip, spring, and tip cleaning wire.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend the 226 generator as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
Fits models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
Also known as part number 5010000290.
This one blue Flourosilicone O-ring. It is resistant to fuel and oil environments. Used inside of many newer lanterns and stoves. This is size #8
This has been reported to be the correct size to repair the valve on the 400B and the 533A stoves. One is needed for both.
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
New Generator for Model 226A700 and the 226-700. New generator includes new gas tip, spring, and tip cleaning wire.
Also known as part number 3000005088.
This also fits 222 models, but please read on.
Coleman discontinued the 222 generator, and they recommend this as the replacement now. In practical use, people have found that it will work and work well, but the heat shield will need fabrication or if using this on a 222, you should install a different heat shield set up out of a 226/229 lantern. The heat shields are not a part that can be ordered as they have been discontinued. This generator is wider/fatter than the original 222 generator and essentially conflicts with the heat shield. The part number for the heat shield is 5414-4605.
O-ring for many Canadian lanterns. O-Ring size is #9, made of Flourosilicone.
We have been told that these will fit the 533 Stove - 2 are needed.
Used filler cap with lanyard for the small backpacking lanterns - in very nice shape. Will also fit most other lantern and stoves that use the standard size filler cap. Comes with a new gasket that you will have to install.
Mica globe for the small backpacking lanterns. Will fit models 222, 226, 229, 3022, 3023, 3150, 5130, 5133, 5134, 5136, and 5414. This globe is approximately 3 3/16 inches tall and has a 3 3/16 inch diameter.
Would be good for camping as it will not break like glass.
Fits the fuel tube on all appliances that have a plastic fuel and air tube.
Models: 214, 282, 285, 288, 290, and 295.
Also fits:
This is the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
This is a 10 PACK of the cardboard tube that goes inside of the 200A and 220 size generators, and many others.
Used cardboard tube that goes inside of the 200A and 220 size generators, and many others.
These mica panels are 3" x 5" in size.
General information:
Used pump assembly with plastic cap, works on the newer stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
This is a replacement pump assembly, made by Coleman for most stoves and lanterns except for the small Peak 1 type products that have a shorter pump rod.
This pump comes with the neoprene pump cup and has parts you can exchange to match your existing type.
This is a new Coleman made replacement pump cup for all lanterns that came with the rubber style.
Graphite ribbon. It is 1/4 inch wide and 12 inches long. It is scalloped to make it more flexible for wrapping. Works for tip cleaner assemblies or any other thing where the normal graphite packing won't fit. It is easily cut with a pair of scissors to fit whatever you might need.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
This is the gasket for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is a 10 PACK for the one-piece filler caps. If your filler cap looks like the one pictured, then this gasket is the correct one. If your filler cap has a screw in the center of it, then this gasket will not work. The red filler cap is shown for illustration purposes only and is not included.
Also known as part number 425A1361
This is 12 inches of new clear plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
This is 12 inches of new black plastic bail wrap to protect the fount of any lantern. The size of these are small enough where it stays put after installation and will not slide around easily. 12" is enough to use on two to three lantern bails.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a new brass retainer ring used on the bottom of many Coleman valve stems. This is designed for a 1/4" valve stem diameter, but can be cut for the smaller 3/16" versions if needed. You will need to open it up, place it over the valve stem, then bend it back. This is used to hold the bushing in place in front of the valve stem packing.
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
This is a 10 PACK - Typically used to stop a fuel leak from the valve stem on older appliances.
This is the larger valve stem packing. It is 5/16" long. The hole diameter is 1/4". It would be used on most modern lanterns, lamps, and stoves. This will only work on valve stems that are 1/4" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
425F stoves could use either this or the P2 packing. Make sure your stem diameter is 1/4" for this part. If it is smaller, you need the P2 HERE.
Coleman made the same product under two different part numbers. This is the same as part number 118B6201 and 118D6201.
Made of 100% graphite.
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many. Comes with a new gasket that you will have to install.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.