Search

New Old Stock M1950 burner frame.

This is a used burner frame for the AGM 2572 lantern.

Used burner frame for the model 2572 lantern.

Burner frame for the model 5152 lantern only. Will not fit the 5152A.

These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.

New 200 burner frame Pal Nut is HERE.

New 200 burner frame Nut is HERE.

This is a reproduction stainless steel burner frame for the model 202. It will also work on all models  200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.

This is a used burner frame for the model 200A lantern. 

This is a used burner frame for the model 200A lantern.

This is a used old style burner frame originally used on the black band 200A Lantern. Looks like someone may have replaced the tabs - they are supposed to be short.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns. 

Is stamped with 3000.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.

This one will need a new burner cap or screen.

Is marked with 3000.

Used burner frame that will fit models 220B through early 220F through approximately 1971.

This is a used Burner frame for the 242A through C lantern. Will also work on the 247. 

Is stamped with 3000.

This is a new reproduction frame for burner frame for the models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.

Used frame for the model 275 and 275A lantern.

Used burner frame for the models 228H and 228J lanterns.

Used burner frame for the models 220H and 220J lanterns. 

Used burner frame for the models 220H and 220J lanterns.

Used burner frame for the models 228H and 228J lanterns.

New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.

These will not fit the 530 stove without using a 1950 generator and a 530 needle.

Burner cap. Similar in size to the Coleman 220 burner cap.

I believe these are burner tubes for an AGM double mantle lantern. They are 2 7/8 inches long. Roughly the same diameter as Coleman burner tubes. Made of steel.

Unknown ceramic material type of burner button used on some heaters and stoves. This has a diameter of 3/4 and is 3/4 tall.

Don't know what this came from. It is about 4 7/8" long, the smallest end is about 3/4" wide and the biggest end is about 7/8" wide. From wing to wing it is about 2 1/2" wide.

This is a reproduction burner ball for the Focus 5 heater. Has been field tested and works excellent. Comes with instructions on how to remove the screen from your old ball and install the new - see those instructions in the "Description" area below. Made of stainless steel. The smaller inner screen would need to be good on your current burner for it to work correctly. Made in the USA.

This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.

New burner screen for the models 236, 237 and 249.

Burner ring measures 2 7/8 inches diameter.

Used burner assembly for the Thermos 2 mantle lantern. In good shape.

Used burner frame for the 288 or CL2 lantern.

Frame assembly for Leisure line lantern

Frame bolt. Fits the 5107C, 5114C, 5151, 5152. May fit others.

Burner assembly for the model 5150 propane lantern.

New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉. 

Sheets are 4-3/4" in diameter and 1/32" thick.

Burner frame assembly for the model 5152A lantern.

Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.

Need the washers for under a 200 or 200A frame? Look HERE.

Nut for 220H through K frame bottom.

This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below. 

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping and one small dent on the outer rim (see photos).

This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)

This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

This vent will fit only the 220F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on models G, H, J or K either. Please make sure the top of your 220 looks like the photo below. 

If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.

Used frame bottom plate for the model 290A and all 295 models. This is a used part and conditions vary one to another.

Burner assembly for the model 214 lantern.

Burner tube

Burner screw for Thermos stoves.

Burner cap with 3 holes for Thermos lanterns.

Burner plate. Has a 2 1/2 inch diameter.