- May 1, 2024Gather 'round, fellow GPA enthusiasts!Our annual convention is fast approaching, and guess what? Itβs practically in our backyardβjust 40 miles from our OCP home! June 27 to 29, 2024
Search
44 products found
Sort by:Recommended
AGM Iron Generator - E1287
I believe these generators are for an AGM iron. They measure 4 inches long.
Canadian Iron Valve Stem, E-1572
This is a valve stem for a Canadian iron, but we do not know the part number or which models it fits. The length of the entire shaft from the base of the handle to the tip is 1/5". The valve stem has been drilled out and can accept a rod.
Iron Pump Reproduction - R305
Reproduction small pump for the Coleman irons. Will also work on any Coleman lamp or lantern.
Reproduction Iron Filler Cap - R306
Reproduction iron filler cap. Fits most irons and other appliances that take a small filler cap.
Iron Slot Cleaning Tool - E1382
Original slot cleaning tool for Coleman irons. New old stock but will show signs of rust and tarnish.
Iron Handle Blue, NOS - E1265
Wood handle for the blue Coleman irons. Was also used on the 242 reflectors.
Iron Pump, Screw Style, Used - E1301
Used original old short pump for Coleman Irons. Will work on lamps and lanterns too. Pump barrel is approximately 5 1/4 inches long. This is a used pump but it will have a new pump leather and will work just fine. This is the early style pump with the wooden sleeve and screws holding the pump to the barrel.
Gray Iron Burner Cap, NOS - E1409
Only 1 left in stockNOS Burner Cap for the early stove models 2, 9, 2C, 9C, 2E, 9E, 2F, and 9F
Cannot be used on the Model 1.
Iron Filler Cap, Nickel Plated, NOS - E1653
These are NOS iron filler caps that are nickel plated. They are a bit dusty from rolling around on a shelf, but should clean up nicely. Fits most irons and other appliances that take a small filler cap.
Cast Iron Scrubber, 4x4, Stainless - E1436
Only 6 left in stockSmall 4" x 4" Stainless steel cast iron cleaner for grills, BBQ's, and cookware. Good size to take camping.
Valve Stem - E1228
Valve stem for the 220 and 228 slant lanterns. Also fits the 4A, 609 & 609A irons that use the 604-299 generator similar to the R55.
- New!
- Free Shipping
Old Coleman Parts Patch Year 13
Supply is limited to what is left over from previous years. Heavy duty embroidered patch with iron on backing. Measures 3 inches diameter.
- Free Shipping
Old Coleman Parts Patch Year 12
Supply is limited to what is left over from previous years. Heavy duty embroidered patch with iron on backing. Measures approximately 3 inches diameter.
Tilley Handle - E1452
Handle for the Tilley model DN 250 and DN 250A iron. New old stock but may have some scratches from storage over the years.
CQ Lamp Wrench, Used - E1368
Only 2 left in stockFrom Terry Marsh's site: This wrench came with a Coleman L220 lantern dated Aug. 1928. The instructions with the lantern identify this wrench as part no. 362-950. It is 4β³ long and fits nut sizes 11/16, 7/16, & 2, 5/16β³ plus a 5/32β³ slotted generator tip remover. This wrench also came with iron Models 4A & 609. Β Link is HERE.
Q77 Generator Nut - S166
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
Handle Bolt, NOS - E1583
Handle bolt for Coleman irons. Also used on the old wood handle lantern reflectors.
Valve Body Type 3 - E1335
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve Body Type 5 - E1365
Valve body for irons. The upright piece is 1 1/4 inches long. Takes a generator that would be held on with a 605 gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve Body Type 2 - E1076
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve Body Type 1 - E1165
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with an R55 style gen nut. Fits models 4, 4A, 8, 8A and the 609A.
Valve Body Type 4 - E1330
Valve body for irons. The upright piece is 1 inch long. Takes a generator that would be held on with a 605 gen nut. The upright piece has a screen in the end of it. Fits models 4, 4A, 8, 8A and the 609A.
Small valve stem packing - P02
Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.
Small valve stem packing - π‘ππ¬ π£πππ - P02
This is a 10 PACK. Typically used to stop a fuel leak from the valve stem on older appliances.
This is the smaller valve stem packing. It is 5/16" long & the hole diameter is 3/16". This will only work on valve stems that are 3/16" in width.
If you need to check your model, please see the PARTS DIAGRAM PAGE.
Typically this is used on the old 327 Quicklites, 427 lanterns and early CQ lamps, irons and some lanterns with the smaller diameter valve stem. The early 425F stoves use this, but could also use the larger P1 packing. Make sure your stem diameter is 3/16" for this part. If it is larger, you need the P1 HERE.
Made of 100% graphite.