Valve Wheel Screw - S77
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
Valve wheel screw. This is the later self taping screw. Fits most lanterns. Can be used where a 17-059 is needed.
These screws are for lanterns requiring a slightly larger and longer fastener than typically found on a 200 lantern. These fit the 236, 237, 220B, and many other older lanterns. Size is 4-40 x 5/16".
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
Used dark red knob for the 530 stove. Same as the 200a or 220 knob just a darker burgundy color.
Looks like it may have gotten a little too hot and burned (see photos)
Used valve wheel for the model 200A lantern. These have burn marks or other defects such as chipped edges. The wheel will still be solid and very usable, just not cosmetically very good.
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
Used maroon valve wheel for Coleman stoves. Has the solid style backside as was common on the earlier stoves. Completely interchangeable with valve wheel 425-1491.
Used valve wheel for many of the Coleman made Sears single and double mantle lanterns.
These are for the Sears valve wheels, they are a bit longer than the usual screws for most valve wheels and therefore will not work on others.
This is a used part and may show signs of wear or have a few chips in it. This is the new style black valve wheel for 200A's, models 220H, 220J and 220K, 228F and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. The main difference is the hollow style back. In the 426 stove series, this only fits 426 or 426A
This is a used part and will show signs of wear, sun fading, or burn marks. This is the new style red valve wheel for 200A's, 413G, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is the old style NOS red valve wheel for 200A's, 502 stoves, 220/228's and others. It is completely interchangeable with the black wheel. Newer model 200A's and model 202 took the black wheel.
This is a used part and will show signs of wear. This is the old style red valve wheel for 200A's, 502 stoves, and others. It is completely interchangeable with the black wheel.
This is a used part and may show signs of wear. There may also be a few small chips in it. This is the old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. It is the solid back style.
This is a NOS old style black valve wheel for 200A, 202, 220D, 220E and 220F, and others. It is completely interchangeable with the red wheel. Newer model 200A's and model 202 took the black wheel. May have some minor scratches from sitting around all these years.
Used valve assembly for the 247 Kerosene lantern. This has a valve wheel that has a screw, unlike the common molded valve wheel.
We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
A graphite valve stem packing is included with each of these in case you end up needing to change them.
NOS valve minus the generator and valve wheel, for the model 425 series stoves.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
New valve stem packing has been installed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
Used valve assembly for 200 and 200A lanterns. In good condition. Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 242b & 242c lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 242 models.
N.O.S Valve stem for the model 335 and 339 lanterns.
Has a small chip on the valve wheel.
Used valve assembly for the models 242 through 242C lantern also 243 & 243A. We have not done any repair work to these at all. We will check to make sure the tip cleaner lever moves as it should and the eccentric block goes up and down.
Valve stem packing has not been changed but one will be included for you to change if needed.
This will also work on the 200A lanterns. The difference is that the original valve wheel comes off with the 200s and the original valve wheel does not come off on the 242s. If you don't care about the valve wheel, these will work for the 200 models.
This is a new old stock pre-heater valve for the M2 military stove. Does not have the valve stem or wheel (knob).
NOS valve assembly for the early model 220/228D that had the solid molded on valve wheel.
Reproduction valve stem for the model 200A lantern. Comes with a new valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
This is a used valve assembly for the model 220/228B lanterns. It has the drain plug. Has the older style fuel and air tube. This valve has a square stem head and will not work with a more modern valve wheel. This valve was used on the 220/228B lanterns and on the early 220/228C lanterns. Packings have not been replaced.
New lamp valve for models 129, 134, 138, 150 kerosene lamps. I believe I have identified the correct part number but am not 100% sure. This valve screws directly on to the upright pipe. It does not have threads to screw on a fuel and air tube. It takes a 220 body generator body. When looking straight at the valve wheel the tip cleaner is on the right and the air tube would be on the left.
For the model 520 stove. New generator includes new gas tip and tip cleaning wire. LINK for great info on these and what they fit.
Additional info: The 520 (aka M1941) and M1942 generators are usually interchangeable. The only exception is the early version of the M1942, known as the Mountaineer Stove. It has a vertical sprocket-type valve wheel. The generator on that stove seems to be unique in that it's a bit shorter than the later version.
Unknown NOS valve stem with fiber wheel. Stem measures 1 1/4 inches.
Unknown NOS valve stem with fiber wheel. Stem measures 1 1/4 inches.
Does not come with packing or valve stem nut.
NOS valve stem with the fiber wheel for the early Coleman lamps. Will not fit lanterns. Fits model CQ, BQ, PQ, 117A, 118A, 119A lamps and others.
Reproduction wooden knob for the M1942 stove tip cleaner. Made of solid walnut. Identical to the original.
This is the small red plastic knob that goes on the end of the tip cleaner assembly on many Coleman appliances.
Some of the models are: 201 lantern, 502, 508 models, 533, 400 models, 440, and the 3024.This is a reproduction part and looks like the original.
Knob for the 282, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.
Used knob for the 282, 285, 286, 288, 290, 295, 295A and 639 lanterns. May fit others also.