This gasket is for many lanterns, stoves, and lamps that take the standard 3 piece filler cap.
If your filler cap is a standard size and has a bolt in the center then these gaskets will work.
Red 3 piece filler cap shown for demonstration purposes only.
This is the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
This is the common Coleman check valve and air stem that fits most styles of lanterns and stoves made after 1946 and some before that date. These are the updated design that uses a smaller head on the air stem. You won't need your current air stem any more as this comes with a new one that is updated and replaces your old one.
If your part diagram calls for the 242B5381 or a 621-5361 check valve, then this would be the correct part. It is also known as part number 2006381ZCL.
This is a new brass one piece filler cap made by Coleman. Comes with a new gasket and will fit most all lanterns and stoves other than the model 242 lantern and 500 stove that have the smaller filler caps.
It is also known as part number 425A1405.
This is the gasket that goes between the propane regulator and the small propane bottles that you screw on. Not ever offered as a separate Coleman part. The total diameter is 15/16 of an inch. The inner hole diameter is right between 5/16 and 3/8 of an inch.
This fits many applications for propane appliances.
O ring made of gas resistant Viton. Outer diameter 7/16". Works on many propane stove models such as 5400A.
Two required for the model 550 stove.
Stainless steel filler cap screw for the 3 piece filler caps used on the 200A, 220B, 220C, 220D, 220E, 220F, 427 and similar sized filler caps.
Fits the cap number: 220C1401
Small thin O ring for the common Coleman check valves. Made of gas resistant material.
Used pump clip that fits most lanterns and stoves. It is used but in fine shape.
This is a new 2 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
Smaller size pre-heater cup for the 201 lantern. Is 1 inch in diameter and the center hole can accommodate a maximum of 5/16".
This is a reproduction inner disc for the old 3 piece caps. Comes with a new gasket and is made of brass.
Screw for tip cleaner assembly to air intake tube. Flat head screwdriver type used on earlier 220/228 models.
Screw for tip cleaner assembly to air intake tube. Phillips head screwdriver type used on later 220/228 models.
Used valve wheel screw. Will be in good condition. These will not fit the 236 or 237.
This is a reproduction burner ball for the Focus 5 heater. Has been field tested and works excellent. Comes with instructions on how to remove the screen from your old ball and install the new - see those instructions in the "Description" area below. Made of stainless steel. The smaller inner screen would need to be good on your current burner for it to work correctly. Made in the USA.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is a large filler cap gasket for the Handy Gas Plants. It also works for the Tilley R1 heater.
This filler cap is made by the Amish so you can pump up your lantern or stove with a bicycle pump. Fits most all styles of lanterns and stoves.
This is for one used 3 piece filler cap.. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first. We are showing 3 caps for demonstration purposes only to highlight the condition it could be in. This is for only one cap, not many. Comes with a new gasket that you will have to install.
Pre-heater cup for the model 237 lantern. This is a new production cup made out of brass. It is very high quality and fits the 237 nice and snug. Will also fit a 530 stove if you want to install a PH cup on it.
This is a new metal filler funnel. Small and easy to pack. See its size in the last photos where it is being used on a fount. Works well for standard sized filler caps. Will not work for the smaller filler caps on models 242, 243, 247, 249 lanterns with the smaller cap or the 500 stove.
This 10 pack of gaskets are for many lanterns, stoves, and lamps that take the standard 3 piece filler cap. If your filler cap is a standard size and has a bolt in the center then these gaskets will work. Red 3 piece filler cap shown for demonstration purposes only.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
This is a used one piece filler cap. Paint is chipped or missing - each one will vary in wear. Comes with a new gasket foryou to install.
Reproduction cast aluminum pre-heater cup for the rare 242K lantern. Most of the 242K lanterns are missing the original pre-heater cup. If you are a purist and want to complete your 242K project then you will be very pleased with this. Looks identical to the original.
This is for one used 3 piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
We are showing 3 caps for demonstration purposes only to highlight the condition it could be in - This is for only one cap.
Comes with a new gasket that you will have to install.
This is a used one piece filler cap. Paint may be chipped or missing andwill vary in wear. Gray in color like the new production Dual Fuel models. Includes a new gasket for you to install.
Reproduction brass pre-heater cup for the model 249 lantern.
This is a 10 PACK of the common Coleman pump cup that fits most lanterns and stoves.
Has a 7/8 inch diameter and is made in the USA of oiled leather.
Generator for the Canadian model 519 heater. New generator includes new gas tip, spring, and tip cleaning wire. Also known as 519-2991.
This is a one piece filler cap. They are in various stages of wear. Paint is chipped or missing and could look like any of these in the photo. We start by handing out the ones in best shape first.
Comes with a new gasket that you will have to install.
New old stock filler plug for catalytic heater.
This is a new production stainless steel element for the Coleman Hot Ray heaters. Replaces the old ceramic radiant that is usually broken or missing.
This is a gasket sealer that many use for sealing valves to tanks. Is flexible when dry and offers good fuel resistance.
NOS check valve for the 345 Kerosene stove, 348 Alcohol stove, the 5B radiant heater and some large kitchen range type appliances. This is larger than all the other Coleman check valves that are commonly used in lanterns and military applications. Width from side to side on top of the threads is 5/8".
This is a new 8 oz. gas bottle used to fill gas lanterns, stoves and lanterns.
This is a reproduction air stem for the large filler caps as used on Handy Gas Plants, Radiant Heater #2, Remote Tank 457 and 465, and other large tanks.
This is a new 8 oz. alcohol bottle for kerosene lanterns. Typically used to fill up the pre-heater cup before lighting.
Reproduction air stem for the Quicklite lanterns and lamps. Also fits the Model 16 heater.
Used nickel plated one piece cap. Fits most lanterns and stoves except for the model 242 lantern and model 500 stove.
Wear and finish will vary.
Comes with a new gasket that you will have to install.
Used handle for the 511A, 512, and 512a heater.
Used pump assembly for most stoves and lanterns except for the small Peak 1 type products. We have replaced the neoprene pump cup.
NOS Direction disk. Small disk with little less than a 3/4 inch diameter. Mostly used on propane stoves - will be way too small for a GPA lantern or stove.
Used filler plug for catalytic heaters, green color. Gaskets seem in really good shape
