This is a new leather pump cup, push on nut and back-up plate. This will fit most all lanterns and stoves. If converting from a rubber pump cup, make sure you use the new back up plate in this kit.
Also known as part number 3000005094.
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
These are a new Coleman made 2 pack of ball nuts. This is the common sized ball nut used on most Coleman lanterns.
Also known as part number 3000005384.
These come in a pair of 2. They are new stainless steel washers that go under the burner frame on all 200 and 242 lanterns. Identical size as the originals.
New 200 burner frame Pal Nut is HERE.
New 200 burner frame Nut is HERE.
Used generator nut for all the model 200, 242, 243, 220, and 228 models. It is in fine shape, just dirty.
Used ball nut. Fits most Coleman lanterns. Will be in fine shape just not shiny and new.
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
This is a used pump assembly. It has been cleaned and has a new pump leather installed. This is the earlier style pump assembly with the square nut to hold the leather. See part number 242D5201 for the later style with the push on nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Brand new Coleman made neoprene pump cup with a large push on nut made by Coleman. Fits pretty much all Coleman Stoves And Lanterns.
Also known as part number 6391091
Reproduction brass ball nut for the model 242A, 242B, 242C, 242K , 234A and 247 lanterns.
Lock Nut for the 200A lantern. Goes on the top end of the burner tube.
This is a new Coleman made generator for Model 290, 290A and 295 Lantern. Each includes new gas tip, spring, and cleaning needle.
This generator can be used on the 290 series lanterns, but you will have to use your original generator nut instead of the new one that comes with this generator. The 290 generators have been discontinued.
These are also known as part number 3000005404 and replaces the 290 & 290A part number of 290-5891.
Original NOS generator nut for the Milspec lantern. Military part number 6260-00-161-1859
Used Generator nut for the model 214, 222, 229, 286, 288 290, 635 and 639 lanterns.
Stainless Steel burner frame to valve nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
Reproduction valve stem nut for the model 200A lantern. Also fits the 202, 242, 243, and 247 series lanterns and also the 425F and G stoves. Does not come with the new packing.
These came out of the old SMP factory. This is the washer that goes behind the pump nut on an SMP military lantern.
This is a used pump assembly. It has a new pump leather installed. This is the later style pump assembly with the push on nut to hold the leather. See part number 200A5201 for the earlier style with the square nut. Both pumps are identical other than that. This pump assembly will fit almost everything Coleman ever made beginning in about 1946 and many models before that. Does not fit the small Peak 1 lanterns or stoves.
Push on nut for pump. The large push on nut is used with the neoprene pump cup.
Reproduction shade holder rod with nut. A lot of the later style US lamps took this type rod.
Reproduction brass generator nut for the model 530 stove. Also correct for the model 237 and 249 lanterns.
Single Ball Nut. Fits all Coleman lanterns except the 242 type models.
Reproduction generator nut for the Q77 generator. Same gen nut also used on the Q99 and R55 too. Also fits on iron models 4, 8 and 8A.
Nut used for the top of the valve on 214, 286, 288 and 290 models. May have other applications also.
Vent nut for the Northstar lantern.
Used ball nut. Came on the model 275 and 275A lanterns, but will fit all Coleman lanterns except the 242 type models.
This is a used pump square nut.
Comes with one square nut ONLY.
Solid brass nut for the model 345, 348, 500, & 502 stoves. Possibly used in other applications also. Refer to the parts diagram of your model if unsure.
Nut for 220H through K frame bottom.
Reproduction generator for the Sunshine Safety lanterns and lamps. Similar to the Coleman Q99 but has a different nut. Will not work on Coleman lanterns and lamps.
Reproduction generator nut for the 252 military lantern. Made of brass.
This is a reproduction generator nut for the first Coleman lantern, the Arc lantern.
Valve stem nut for 220, 228, 275 Lanterns. Also fits the M1942 Stove. May fit others.
Globe nuts for the Thermos and Kamplite inverted lanterns.
Reproduction generator nut for the 500 and 500A stove.
Valve stem nut for the model 214, 242 and 200 series lanterns.
Small nut for bottom of stove grate.
Reproduction valve stem for the model 200A lantern. Comes with nut and graphite packing, and valve wheel screw.
This will work on the 242, 243 series lanterns but you won't be able to use the original type knob that was molded on the end of the valve stem.
Reproduction generator nut for the 335 and 621 lanterns.
This is a used vent for models 227 and 228B through 228E. Very nice vent. Has a small dent/rust where the ball nut sits (see photos).
This is a used vent. It will fit models 220B through 220E.
Has paint chippings and a small bulge towards by the ball nut opening (see photos)
Reproduction Canadian brass ball nut for the model 242A, 242B, 242C, 242K , 234A, 249 and 247 lanterns.
Used ball nut for the model 275 lantern. This is the checkered variety.
Unknown used ball nut. Kind of like half a ball nut.
Used wing nut for the milspec lantern.
NOS Jamb Nut for all the model 200, 242, 243, 220, and 228 models. Came from an old parts bin in a Coleman service center.
NOS generator nut for the model 500 and 500A stove.
