Search
Focus 5 Burner Ball Reproduction - R703
This is a reproduction burner ball for the Focus 5 heater. Has been field tested and works excellent. Comes with instructions on how to remove the screen from your old ball and install the new - see those instructions in the "Description" area below. Made of stainless steel. The smaller inner screen would need to be good on your current burner for it to work correctly. Made in the USA.
- Free Shipping
220 Burner Screen - S30
Burner screen for the model 220 and 228 lanterns. Fits most double mantle lanterns and lamps with small burner caps.
Burner Frame Stainless - R350
This is a reproduction stainless steel burner frame for the model 202. It will also work on all models 200, 200A, 201, 202, 5101, 5121 and 5122 lanterns.
Burner Tube Brass 2 7/8 - E1254
Brass burner tubes for most Coleman double mantle lanterns and lamps. Measures approximately 2 7/8 inches long.
Burner Tube with Nut - Steel - E1127
Steel burner tube and nut. A little longer than the normal 242 burner tube. It is 1 1/8 inches long.
Burner Tube, Brass, NOS - E1269
New old stock burner tube for the model 242, 243, 234, 247 series lanterns. 15/16 inches long.
288 Heat Shield - C032
Fits models 288, 288A and 288B lanterns. If you need it for a 288, it will fit down inside your frame, but it is some work to get in there. It will not cover the lighting holes.
The frame bottom is replaced if your current lantern has riveted in springs. This one will accommodate the updated spring configuration.290/295 Heat Shield - C042
These fit all 290 and 295 model lanterns.
- The 290 was originally made with a full frame and did not come with a heat shield, so this version is a bit of work to get installed. Once in place, it ends up covering the lighting holes in the bottom of the frame - FYI.
- On a 290A and 295, you will need to replace the frame bottom also if yours has riveted in springs.Burner Cap & Rings - C054
Burner cap and rings for the 400, 400A, 400B, 440, 442, 508, 533, & 3024 Stoves
Auxiliary Burner Bowl and Rings - C053
Auxiliary Burner Bowl, Rings And Screw 413E/413F/413G/424/426B/426/D/426G/442/442A/443 Instant Light, 2 & 3 Burner Stoves
Burner Cap 220 Brass Round, NOS - E1044
NOS burner Cap 220 Brass. Fits most models of double mantle lanterns and lamps. For nickel plated caps see part 112-3231.
288 Burner Assembly Brass - C070
Burner assembly for the model 288 lanterns. The burner tubes are brass.
Burner Cap - 200/242 - C009
This is a new Coleman made burner cap for the the 200, 200A, 202, 243, 242 and 247 lanterns. Also fits a few lamps and Sears lanterns.
Also known as part number 2423231.Burner Cap 220 Steel Hex - E1267
Steel burner cap for most models of double mantle lanterns and lamps. Has hex head for easy installation and removal.
Burner Cap 220 Steel Round - E1662
Round steel burner cap for most models of double mantle lanterns and lamps.
Burner Cap 220 Nickel Hex - E1096
New nickel plated brass burner caps with hex head. Fits most models of double mantle lantern and lamps.
Burner Cap 220 Brass Hex - S32
Brass burner cap with hex head for easy installation and removal. Fits most models of double mantle lanterns and lamps.
Solid brass with stainless steel screen.
Same part number as 112-323
Burner Screw, Flat Head Steel - S71
Stainless steel screw for the burner ring assembly on Coleman 2 and 3 burner suitcase stoves. Also same part as 413-130 but this is a slot screw instead of phillips.
228 Vent, Small Frame, Used - U887
This is a used vent. It will fit models 228F through 228J. This vent has some paint chipping (see photos)
This vent will fit only the 228F model with a smaller burner frame made up to about 1971. After that, the F model used a different burner frame that included 4 bumps where the uprights are fastened. The mounting location is only 5-1/8" on this vent. This vent will not fit on late model F with the wide burner frame or models G, H, J or K either. Please make sure the top of your 228 frame looks like the photo below.
If the top of your burner frame has bumps, this vent will not fit. See photo below for an example.
Burner Assembly Steel Used - E1660
Burner Assembly for the model 288 lanterns. The burner tubes are steel. Will vary in wear.
Burner Tube Steel - E1480
Steel burner tube for the 220-228 series lanterns. Measures approximately 2 7/8 inches long.
Burner Tube Steel - E1357
This steel burner tube was used on the 242b and 242C war time lanterns. 15/16 inches long.
Valve Stem Assembly - E1498
Valve stem assembly for burner 556; generator 486-262; handy gas plant 458, 458G; heater 15, 16; and stove 373.
- Free Shipping
Burner Screen - S29
This replacement screen will fit the burner caps used on 242 and 200/200A model lanterns.
Pre-Heat Generator - E1110
Pre-heater generator for the Urn Burner 404, 505, 707; Water heater 1; Handy Gas Plant 5052; Pre-heater 544-383.
Pal Nut - S67
Pal nut for the 200, 200A, 201 and 202 lanterns. Also used on some stoves.
Need the washers for under a 200 or 200A frame? Look HERE.
- Free Shipping
- New!
242 Burner Frame, Used - BF504
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
Is stamped with 3000.
- New!
242 Burner Frame, Used - BF505
This is a used Burner frame for the 242A through C lantern. Will also work on the 247 and other similar lanterns.
This one will need a new burner cap or screen.
Is marked with 3000.
220 Burner Frame, Used - U920
Used burner frame that will fit models 220B through early 220F through approximately 1971.
M1950 Burner Bowl - E1271
New old stock burner bowl for the M1950 stove. Shows some tarnish from sitting around for years.
These will not fit the 530 stove without using a 1950 generator and a 530 needle.
Wrench 220B - R300
Wrench for the lantern models 220/228B through 220/228F. Fits the small nut at the bottom of the burner frame. Angled to fit that hard to get at nut. It is a 9/16 wrench.
Burner Ring Gasket Material - R515
New fiber gasket material - you will have to trace your burner bowl out and trim it with scissors. This is only for the gasket material - photo to show original look only.
These are used under the burner rings of some of the newer Dual Fuel suitcase stoves like the 414 and 424A. Most likely used on others too. We have measured some to have an outside diameter of 2-3/8 inches.
These are made of a ceramic fiber paper that can withstand 2500℉.Sheets are 4-3/4" in diameter and 1/32" thick.